Identifying Hub and Bearings for 2001 Prestige Trailer

Question

Question:

Do you happen to know the part number for either the wheel bearings for a 2001 Prestige trailer or the hub part number?

asked by: Jeff H

0

Expert Reply:

Hi Jeff; I'm assuming you were able to identify the parts based on the axle tag or by pulling off the hubs and measuring. Did you verify that the grease seal had a 2.25" inner diameter? The # AKIHUB-655-6-EZ-K comes with a 2.25" ID grease seal, and that matches the # GS-2250DL you ordered as well. However, the same axle capacity can also use a 10-10 grease seal # RG06-090 with a 2.125" ID so I recommend double checking if you haven't just to be sure.

Any big trips coming up with your boat?

expert reply by: Robin H

0

GS-2250DL Grease Seal
(click to enlarge)

Jeff H.

8/24/2025

I checked and you are correct. I should have ordered the seal with a 2.125" ID. Thank you for pointing that out.

Robin H.

8/25/2025

@JeffH you're welcome. The good news is the seals are relatively cheap and you can swap them out since they fit the same hub.

Jeff

9/1/2025

@RobinH I noticed when replacing the bearings on the other side of the trailer the outer bearing part number was LM67048. I should have everything I need now. Thank you again for the help.

Robin H.

9/2/2025

@Jeff stick with the # 15123 that came with the hub or the # TMK34FR you ordered if you're swapping the included bearings with Timken. The inside diameter of both bearings is the same at 1.25" but the # LM67048 will have a different outer diameter so it won't fit the hub properly. Basically, both will fit the spindle, and in that aspect can be used interchangeably. However, both will not fit the same hub.

Answer 1

If you give me the tapered spindle measurements like in the attached photo, I can help you get the replacement hubs you need. I need the measurements at letter B where the seal sits, letter C where the inner bearing rides, and letter D where the…

view full answer...

Answer 2

If the trailer is heavy, or the ground is uneven, it will be hard to move regardless of which jack you use but if the bearings are wearing out in the old one then a new one would surely take some strain off the user when moving. I recommend a dual…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Identifying Hub and Bearings for 2001 Prestige Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching