Hi Darrin! The MORryde RV Cargo Slide Tray - 90" x 23" - 2 Way Slide - 60 Percent Extension - 800 lbs #MR78RV can clear a lip up to 1.57 inches, so call it 1-1/2 inches to be safe. If you need it to be higher, we do also have the Height…
Hi David, I called MORyde to check the internal dimensions of the MORyde RV Cargo Slide Out Tray part #MR78RV and they confirmed the internal length is 88.21 inches long and the internal width is 19.84 inches wide. Considering the Blackstone Griddle,…
Hey Alex. From the information I can find online it does look like your 2011 Keystone Cougar 318SAB does come prepped for a second AC unit. The bedroom roof vent should be reinforced and pre-wired for a 13.5k or 15k BTU unit. To check if your trailer…
Hey Phil! For a tandem axle trailer you will want two of the Leveling Kit with Wheel Chocks for Trailers and RVs #WS28ER. You are correct, one under each tire is best. I use these on my Jayco with one under each tire to keep them off the ground and…
The Replacement Controller and RF Remote for Lippert TV Lift System #LC253395 will not work on your existing RV T.V. lift due to the controller being specific to the motor. The motor, Lippert part 325978; has it's own pigtail that plugs into the…
Hey Jonathan, RV air conditioners all fit a 14" x 14" hole so the only real important factors to determining the correct fit for you would be the BTU rating and whether you have a 6-pin or 9-pin connector. The 936000108 part number you…
Hello Herb, It's been a while, thanks for writing in. The short answer is no, the Micro-Air EasyTouch 353 is not currently compatible with the Furrion Chill Cube ducted system like the one included with #FR99TD. The Chill Cube is a newer,…
Welcome back Rich and thanks for the information! To replace your Sharp Carousel microwave R-820BK-F, I recommend the Greystone Built-In RV Convection Microwave item #GR27FR. It measures 21" wide x 11" tall x 15-3/4" deep.…
Hey Mark, welcome back! Yes, that factory damper will be removed to install the Safe-T-Plus Steering Stabilizer #ST98MR. See the photos below. I also went ahead and linked the instructions and an installation video further down on this page for your…
Hello Jerry, Thank you so much for the pictures, they are always most helpful! I am sorry but there is not a seal packing kit, you will need to replace the entire jack. For your Lippert Level Up with part number 343315-RA, you will want the…
In my experience the MORryde Wall Mount #MR82ZR will require additional mounting height to allow it to clear the storage door opening on most RV's. I have had better results using the Mount #MR38DR in the area you are looking to mount the TV.
Fixed RV TV Mounts for steady, low-profile installs
Built for simple, solid installs in RVs or boats, these mounts keep your screen steady on the move. The fixed design offers a low profile and a firm hold, with options that let you remove the TV for travel. You'll also find choices with a variety of mounting hardware, and installs can go fast with basic tools like a 3/8 nut driver, even in tight spaces.
Installation is typically straightforward. A large variety of hardware can make matching your TV and wall easier, and using a 3/8 nut driver chuck on a drill speeds things up. Choose a low-profile design for tight areas. If the TV's plug or tabs interfere, plan careful trimming with a metal blade to get a clean fit.
Some fixed mounts let you lift the TV on and off the base easily. This makes it simple to take the TV down for travel and reinstall at camp. Verify the bracket-to-base interface allows tool-free insertion and removal and that it feels firm once seated.
Match the bracket to your TV and check for clearance around ports. A 32 inch TV fit perfectly for one install, but trimming was needed where the power plug hit the bracket. In tight spots, low-profile designs help the base mount nicely. Have a jig saw with a metal blade ready if a small cutout is needed to clear a plug or tabs.
Yes, fixed mounts can hold firm in motion when installed solidly. They've worked well on RV bedroom walls and held well in a moving boat. Check for robust construction and a firm base-to-bracket connection. If a design uses a hinge between wall plate and TV bracket, it can allow side-to-side movement and rattling; look for bolted connections to reduce that.
Yes, there are very low-profile fixed mounts that won't be obtrusive to an ultra slim TV. Confirm the profile leaves room to route your power plug and cables. Test-fit before final mounting to ensure ports aren't blocked.
Filters
