Hey Alex. From the information I can find online it does look like your 2011 Keystone Cougar 318SAB does come prepped for a second AC unit. The bedroom roof vent should be reinforced and pre-wired for a 13.5k or 15k BTU unit. To check if your trailer…
Hey Phil! For a tandem axle trailer you will want two of the Leveling Kit with Wheel Chocks for Trailers and RVs #WS28ER. You are correct, one under each tire is best. I use these on my Jayco with one under each tire to keep them off the ground and…
The Replacement Controller and RF Remote for Lippert TV Lift System #LC253395 will not work on your existing RV T.V. lift due to the controller being specific to the motor. The motor, Lippert part 325978; has it's own pigtail that plugs into the…
Hello Herb, It's been a while, thanks for writing in. The short answer is no, the Micro-Air EasyTouch 353 is not currently compatible with the Furrion Chill Cube ducted system like the one included with #FR99TD. The Chill Cube is a newer,…
Welcome back Rich and thanks for the information! To replace your Sharp Carousel microwave R-820BK-F, I recommend the Greystone Built-In RV Convection Microwave item #GR27FR. It measures 21" wide x 11" tall x 15-3/4" deep.…
Hey Jonathan, RV air conditioners all fit a 14" x 14" hole so the only real important factors to determining the correct fit for you would be the BTU rating and whether you have a 6-pin or 9-pin connector. The 936000108 part number you…
Hey Mark, welcome back! Yes, that factory damper will be removed to install the Safe-T-Plus Steering Stabilizer #ST98MR. See the photos below. I also went ahead and linked the instructions and an installation video further down on this page for your…
Hey Skip, welcome back! The Vitrifrigo RV Refrigerator w/ Freezer item #VT56FR is going to need a 12v power supply. You can not plug it into a standard 110v outlet. You'll need to use the PowerMax AC to DC Converter item #PM54VR, which works with…
Hey Nang, the mounting holes on the back of the MORryde TV bracket part #MR85ZR can accommodate bolt sizes that are up to M8 in diameter. M8 is 8mm (about 0.315 inches) across its threads, while 1/4-20 is 0.25 inches. Typically TV hardware is M4, M5,…
In my experience the MORryde Wall Mount #MR82ZR will require additional mounting height to allow it to clear the storage door opening on most RV's. I have had better results using the Mount #MR38DR in the area you are looking to mount the TV.
Hey John, welcome back! I do have a way better functional solution for you. It's the Brandmotion Tailgate Delete Backup Camera with Wiring Harness item #BM67JR. This camera attaches to your license plate bracket. The other end will connect to the…
The Lippert Patio Upgrade Kit for Toy Hauler Garage Doors #LC27FR is a complete kit. It has all the hardware and struts that you need to convert your garage door into a patio. It may seem confusing because there were optional side rails that you…
Your internet site is very well organized and easy to use...My order was shipped very promptly and included everything I ordered...All in all this was a simple procedure for what can be a complicated order. I would use your company again or recommend you to others. Your selection was broad and your prices fair.
Robert
Bloomington, IL
RV TV Mount with 25 lbs capacity
Dial in a solid setup for lighter TVs with an RV TV mount rated at 25 lbs. Match your screen's VESA pattern—common options include 75 mm x 75 mm or 100 mm x 100 mm—and pick the style that fits your space, from wall mounts that swing, swivel, or tilt to ceiling mounts that flip down for viewing and stow away. Keep an eye on arm length and drop, since those can limit overall TV size even within the weight rating.
Some do, but not all. Check for a locking position or tension adjustment so it doesn't float out of place. If it won't hold where you set it, increase tension or look for a model with a defined lock. After installation, move the TV through its range to confirm it stays put in both stowed and viewing positions.
Confirm the mount's VESA options and your TV's hole spacing. Many list 75mm x 75mm or 100mm x 100mm, and some wall mounts include 200mm x 200mm. If you need 300mm x 300mm or 400mm x 400mm, look for adapter plates. Weigh your TV to ensure it's under 25lbs, and verify all mounting hardware is included before starting.
Size depends on weight and pattern, not the screen measurement. If your TV is under 25lbs and matches the VESA pattern on the mount (often 75mm x 75mm or 100mm x 100mm), you're set. Arm length and drop can limit larger screens, so a smaller TV may be best on some flip-down styles. Measure the mounting holes and check the TV weight before choosing.
Yes, some flip-down ceiling mounts flip up when not in use and swivel 360 degrees when down with a 25lbs rating. Confirm your TV fits the listed VESA pattern, like 75mm x 75mm or 100mm x 100mm. Mounting outdoors? Make sure your install surface is solid and protected. Verify the mount's motion range matches where you want to watch.
Filters
