The Replacement Standard Dual Rack Repair Kit for Lippert RV In-Wall Slide-Outs - Fixed Side, #LC84FR is the left side of the slide-out as looking at it, facing it, from the outside. The float side, #LC26VR, will of course be the right side as facing…
Hi Ron, thanks for reaching out. I completely understand why you're checking that measurement before ordering since if the fins don't reach the slide wall, the seal won't do the job you're expecting. The Rubber Bulb Seal with Fins for…
Hey Stephen, we have the 16 foot etrailer awning part #e84QV that would work great on your car hauler. How tall is the side of the trailer? It shouldn't be a problem but the arms of this awning are 69 inches tall. We spent a lot of time on our…
Unfortunately, I cannot tell you what wiper seal you would need for your 2004 Keystone Outback. This is not something that is known just from the RV information. It depends on your particular slide-out. The best way to determine what wiper seal you…
Hey Jack congrats on the new Jeep! To flat tow a 2021 Jeep Wrangler Rubicon behind your 2012 Thor Hurricane 31J motorhome, I recommend the following parts: Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Roadmaster Direct-Connect…
Hello Andrew, good question. Basically the only difference between the composite kits and the standard (non-composite) kits is the application they are used for. Composite are used in motorhomes, the other are used on towable campers. It has to do…
Hey Jared, the pass through amp rating of the Rich Solar NOVA 3K12 3000W 12V Pure Sine Wave Inverter with Built-in Transfer Switch for RVs #RS79VR is 30 amps. What AC units do you have? This should be more than enough for that.
Hey Martin, The only difference I'm seeing between the Replacement Motor #TUS24FR and the Replacement Motor #LC125802 is that the TUS24FR has a 9000 RPM rating while the LC125802 has a 440 RPM rating while under load, which jumps up to 500 RPM…
To get right seal you'll need to remove a portion of the seal to get the side profile of your current seal. There are multiple types of applications for slide-out seals; Glue On, Peel-N-Stick, Press In, Push On, and Slide-On. There are multiple…
Hey, Skip! Happy to help get your new Jeep set up for flat towing. There is going to be a list of parts, so I'll go ahead and list them all below for ya. Blue Ox Base Plate: Part #BX1139 Blue Ox Avail Non-Binding Tow Bar: Part #BX7420 Demco…
Hey Donna, you would have to replace the entire setup as there was a refrigerant law change in January of 2025 that forced the complete systems to have to be redesigned and because of that nothing is currently backwards compatible. So what I would…
You've got both a wiper seal and a bulb seal here with the wiper seals having a track for the bulb seal to slide onto. The Rubber Wiper Seal with Track for RV Slide Out #SR87FR you were already looking at is most likely the closest option to what…
RV Slide Out Parts: Actuator for Lippert Through-Frame Slide-Out Systems
Tackle a sticking slide with an actuator built for Lippert Through-Frame Slide-Out Systems. Match your current actuator's retracted length for proper fit, and if only the drive is failing you can replace just the motor to keep things moving smoothly.
Yes, you can replace only the motor. Verify the motor's RPM and gear ratio to keep slide speed consistent. Confirm the bolt pattern on your motor end; some housings have multiple holes that may not be tapped, so be prepared to drill and tap to fit your existing motor bolt. Reuse existing hardware if new bolts or a bracket are not included.
Start by verifying you have a Lippert electric through-frame slide. Measure your actuator fully retracted and match that length. Check for a two-digit stroke marking at the end of the cylinder. Some Lippert 2 inch electric through-frame slides use an actuator with a 2 inch outer tube. If your unit is hydraulic, identify port spacing and system type first to avoid a mismatch.
Installation is straightforward but the actuator is heavy and access is underneath, so plan your workspace. Some actuators may have motor holes that aren't tapped; drill and tap as needed. Have bolts and a bracket ready to reuse if not supplied. Replacing a failing actuator can resolve a slide that hangs up when extending from fully retracted, and can reduce operating noise.
Yes, RPM changes affect movement speed. A lower RPM option, like 5,000 RPM, will slow the slide significantly compared to a 9,500 RPM high-speed motor. Match the original RPM to keep expected performance. Mixing different speeds side to side on hydraulic systems can cause uneven travel, so verify your system type before mixing components.
Hydraulic Parts
Filters
