Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…
Hey Bob. There's two possible locations for the brake controller port on your 2026 Ford F-150. The most likely one is on your dash behind the coin holder above the 4WD knob. It'll be connected to the back of the coin tray which is only…
Hey Brian! Yes, the Firestone Ride-Rite Air Helper Springs #F89VV will fit your 2025 Toyota Tundra. That is just the generic picture attached to that page, I can see how it would be confusing. These are designed to mount over the axle, and are…
Hey Jason! For your 2026 Ford F-450 I recommend the Redarc Tow-Pro Liberty Brake Controller #RED67CR. This comes with a custom wiring harness that will plug into the factory brake controller port under the dash. The Liberty is simple, reliable, and…
Hey Kevin, yes we have the SumoSprings kit part #SS46KJ that is a fit for your 2025 Chevrolet Silverado 2500 HD. This is the medium density foam spring provides 2,800-lb support capacity at 50% compression and also requires no drilling for install!…
Hello Paul, There is one thing I like to have when I'm out enjoying the wilderness, and that's a toilet that feels like I'm at home. Well, I found just that for you. Since you're replacing the Dometic 300 in your 2021 Winnebago Minnie…
That is correct Trevor! The Progressive Dynamics 4500 Series RV Converter w/ Charge Wizard and AC/DC Distribution Panel item #PD4590K18LS8 would be the correct replacement. This is a 90-amp 2-in-1 AC/DC distribution panel and converter charger that…
Your current microwave has the dimensions of 29-15/16 W x 16-7/16 H x 15-3/8 D which is almost identical to the Furrion part #FMCM15SS which we know works really well and is reliable so it would be a really great and easy solution.
Hey Arlen, welcome back! For a hitch I recommend the Curt Adjustable Width Trailer Hitch #13703. This Class III hitch fits 22" to 72" wide trailer frames and can be bolted or welded on for installation. It has a max tongue weight of 350 lbs…
Hey Tim, I checked out your Predator 5000 generator and it does use a quick connect propane connector like what the part #CAM57629 provides so yes this would work. How do you like the Predator generator?
Hey Robert & Carol, That part number comes back to a custom order piece. Is this the channel on the side of your RV that the fabric from your awning slots into, like part #LC715216? If you'd like to email me some pictures I'd be happy to…
While we don't carry a hinge with the exact leaf setup as what you have pictured, the Replacement Controlled Motion Hinge for RV Entry Door - 6 Leaf - Black #LC95VR is still a viable replacement option. Since the leaf configuration is slightly…
Give your entry a clean, finished look by replacing worn screw covers and door edging with trim that snaps into the track. It's a solid fix for door trim and weathered screw covers, and even around closable bunk ends on a hybrid trailer. For radius screen doors with 3 inch top-corner radius, confirm fit by measuring—dimensions like overall height 0.88 inches and 0.75 inches between the lips can help; extreme heat up to 114° may affect shape.
Yes, it's commonly used to replace weathered screw covers and door trim. Match the size and snap profile to your existing track for an exact fit. If your old piece blew off, double-check that the new cover is fully seated along the entire track.
Measure the channel between the upper and lower lips and match that to the trim's snap profile. Check the overall height of the trim and the lip overhangs against your track. If a diagram is provided, compare each measurement before you buy to avoid a wrong size.
High heat can affect some trim. One report from 114° conditions noted the cover started to lose shape and come off the track. Make sure the trim is fully snapped in, inspect it periodically in extreme heat, and consider parking to reduce direct sun when possible.
Yes, snap-in screw-cover trim is used on radius screen doors. Verify your door has rounded top corners and a matching track that accepts a snap-in cover. Measure the channel and confirm the profile matches before installing.
RV Door Parts Parts or Accessories
Filters
