Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…
Hey Bob. There's two possible locations for the brake controller port on your 2026 Ford F-150. The most likely one is on your dash behind the coin holder above the 4WD knob. It'll be connected to the back of the coin tray which is only…
Hey Brian! Yes, the Firestone Ride-Rite Air Helper Springs #F89VV will fit your 2025 Toyota Tundra. That is just the generic picture attached to that page, I can see how it would be confusing. These are designed to mount over the axle, and are…
Hey Jason! For your 2026 Ford F-450 I recommend the Redarc Tow-Pro Liberty Brake Controller #RED67CR. This comes with a custom wiring harness that will plug into the factory brake controller port under the dash. The Liberty is simple, reliable, and…
Hey Kevin, yes we have the SumoSprings kit part #SS46KJ that is a fit for your 2025 Chevrolet Silverado 2500 HD. This is the medium density foam spring provides 2,800-lb support capacity at 50% compression and also requires no drilling for install!…
Hello Paul, There is one thing I like to have when I'm out enjoying the wilderness, and that's a toilet that feels like I'm at home. Well, I found just that for you. Since you're replacing the Dometic 300 in your 2021 Winnebago Minnie…
That is correct Trevor! The Progressive Dynamics 4500 Series RV Converter w/ Charge Wizard and AC/DC Distribution Panel item #PD4590K18LS8 would be the correct replacement. This is a 90-amp 2-in-1 AC/DC distribution panel and converter charger that…
Your current microwave has the dimensions of 29-15/16 W x 16-7/16 H x 15-3/8 D which is almost identical to the Furrion part #FMCM15SS which we know works really well and is reliable so it would be a really great and easy solution.
Hey Arlen, welcome back! For a hitch I recommend the Curt Adjustable Width Trailer Hitch #13703. This Class III hitch fits 22" to 72" wide trailer frames and can be bolted or welded on for installation. It has a max tongue weight of 350 lbs…
Hey Tim, I checked out your Predator 5000 generator and it does use a quick connect propane connector like what the part #CAM57629 provides so yes this would work. How do you like the Predator generator?
Hey Robert & Carol, That part number comes back to a custom order piece. Is this the channel on the side of your RV that the fabric from your awning slots into, like part #LC715216? If you'd like to email me some pictures I'd be happy to…
While we don't carry a hinge with the exact leaf setup as what you have pictured, the Replacement Controlled Motion Hinge for RV Entry Door - 6 Leaf - Black #LC95VR is still a viable replacement option. Since the leaf configuration is slightly…
RV Door Parts with Strike Plates for easy replacements
Swap out worn hardware with durable strike plates matched to RV door parts. Metal options, including stainless and powdercoated steel, give a sturdier latch than plastic and handle exterior use. For a smooth install, compare overall size, hole spacing, opening size, and latch orientation for your entry or compartment door.
Verify whether hardware is included—some plates do not come with screws. Check screw length and head style to match countersunk holes and avoid penetrating thin door skins; flathead screws or pop rivets may be better in some cases. Take time aligning the latch and plate to reduce binding and help the door close easier.
Yes, swapping a plastic plate for a metal one can provide a more secure and strong closure, especially on slam locks. Stainless options can help protect aluminum frames from wear. Check that the plate profile matches your frame, and some installs have stacked the new plate over the factory plastic to reinforce the latch area.
Match the shape and dimensions of your old plate. Measure overall size, hole spacing, and the latch opening, and note the door swing so the opening lines up. Compare to the listed dimensions and drawings. If the fit is close but not exact, minor trimming of the frame cutout has helped some installs line up.
It can if the dimensions match your original strike plate. Cross-brand replacements are fine when overall size, hole spacing, and opening size line up. If it hasn't been tested with your lock, compare measurements from your old plate. If you need a mirrored orientation, you may need to modify the plate or frame opening.
Filters
RV Door Parts Parts or Accessories
