What Size Fitting Is on the RV Tub Drain with Threaded Stopper - 2"

Question

Question:

I wasn’t sure whether the threaded bottom portion fit into a threaded 2” pvc pipe or coupling or something smaller

asked by: Fred B

0

Expert Reply:

In regards to the RV Tub Drain with Threaded Stopper part # 372184030-A, the hole size that the drain is designed to fit is 2" whereas the fitting size that attaches to the drain pipe is 1-1/2".

expert reply by: Conner L

0

Answer 1

The Ultra Faucets RV Drain Plug part #277-000038 has a rubber gasket so plumbers putty is not needed. The rubber gasket will seal the the drain hole.

view full answer...

Answer 2

Not at all! The UniGuard Waterless P-Trap for RV Sewer Systems #LSB24FR can actually be installed in the horizontal or vertical position, whichever works better for your application. The idea of this product is to help save valuable space in your RV…

view full answer...

Answer 3

I recommend a 2" drain plug for the Better Bath RV Bathtub part #LC209648 because it has a 2" drain hole diameter. For a 2" drain plug you would want part #372184030-A.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

What Size Fitting Is on the RV Tub Drain with Threaded Stopper - 2"

Product Page this Question was Asked From

Continue Researching