Hello Steve, Welcome to etrailer, I'm glad you found us! You will need to add the Pollak Mounting Bracket #PK12711U separately. The etrailer Trailer Hitch Receiver #e98850 does not include the electrical connector or a mounting bracket for it. It…
While we don't have replacement parts for a Model 70LP actuator, we do have a great replacement for it. Like the 70LP, these actuators are a fit for a 2" hitch ball, but they just have a slightly larger capacity at 7,500 lbs. You didn't…
The towing capacity of the 2003 Chevrolet Avalanche 1500 with 5.3L V8 and 4.10 rear axle is 8100-lbs. For a 7600-lb GVWR travel trailer the resulting 500-lb safety margin is adequate/low-ish. With a trailer that weighs substantially more than the tow…
Hi Kassi! I do have a couple options that will fit your 2024 Chevy Colorado WT with 2 wheel drive, but the Timbren Suspension Enhancement System - Rear Axle #T83AV is specifically for the 4 wheel drive models. With that said, you will want one of the…
Hey Rick, yes you can use the longer Equalizer shank part #EQ90-02-4500 that you referenced in place of what you have now to get a little more length from your towing setup. While this is longer and would in theory apply more leverage it doesn't…
I would be happy to help you. For your 2006 Kenworth T300 I recommend the Tekonsha Prodigy P2 Trailer Brake Controller item #90885. This controller ties into the brake stoplight switch that's usually located above the brake pedal, which is what…
Hey Brad, to replace your Tie Down Engineering LP70 actuator, I recommend going with the Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-20. This actuator will fit on 3" wide channel tongues, will work with 2" balls, and has a 7,500 lb…
The Furrion #FACR15SA-PS 15,500 BTU unit that you referenced is a replacement for Furrion only and is not offered with compatible ceiling distribution box. I do have a solution though. To replace your Single-Zone, Stand-Alone Dometic Duo-Therm Brisk…
If the front arm/hinge on your Yakima SkyBox Cargo Box like the SkyBox 12 #Y07334 isn't unhooking due to the carrier being over-stuffed, then your only real option is to try and wiggle around your cargo enough to get some clearance between it and…
Based on the number you mentioned you have a 3,500 lb AxleTek hub so for a version that has the 6 on 5-1/2 inch bolt pattern you are wanting you'd need the part #AKHD-655-35-EZ-K.
Hey Neil, so we can help but we don't have a rebuild kit or an exact replacement for the Tie Down model 70lp that you referenced. The Dexter Disc #DX73FR or Drum #DX67FR actuator is going to be your best option. These are weld on actuators but we…
The exact replacement hub assemblies you need for your BD2-545-17 are the etrailer Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 #AKHD-545-35-K that you referenced.
Quick processing, and delivery. reasonably priced very satisfied
Bernie
Krakow, WI
Exhaust Tips with 6 Inch Diameter, Easy Clamp-On
Go big with 6 inch diameter exhaust tips that install with a simple clamp-on setup, no welding or cutting needed. Designed to fit 5 inch tailpipes, you'll find stainless steel options for corrosion resistance and black finishes with a hardened enamel coating for added durability. A clean upgrade without modifying your stock pipe.
Clamp-on 6 inch tips that fit 5 inch tailpipes are not vehicle-specific. If your tailpipe's outside diameter is 5" at the exit, it will work regardless of vehicle. Check clearance around the bumper and make sure you can access the clamp to tighten it evenly.
Clamp-on 6 inch tips do not require welding or cutting. They slide over the existing pipe and secure with a clamp. Verify the tip is a clamp-on style and that your tailpipe diameter matches the listed fit, such as 5".
Stainless steel provides corrosion resistance, and a hardened enamel coating on black finishes adds durability. Look for stainless construction and note if a black tip lists an enamel coating. Tighten the clamp evenly to help prevent loosening after installation.
Yes, when the 6 inch tip is designed to clamp onto a 5 inch tailpipe. Measure the outside diameter of your tailpipe at the exit; if it's 5", a matching clamp-on 6" tip is made to slide over it. No welding or cutting is required on clamp-on designs.
Filters
