Hey Kris, the Dutton Lainson winch part #DL15440 does not come with a strap so you will need to order one with it. The part #DL24250 will work great with this winch as it is correct width, is 25 feet in length, and has a capacity of 3,700 lb WLL and…
Thanks for reaching out Greg, we get this question from time to time. At this time, we don’t offer any tire and wheel packages in a 5 on 4.25" bolt pattern. The main reason is this bolt pattern's typically is found on a passenger vehicle…
Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…
Jason, you only need one Hub Saver per wheel. Since they're sold in a pack of two, one package is enough for a single-axle trailer with two hubs. If you have a tandem-axle trailer, you'll need two packs to cover all four wheels. The Hub Saver…
It looks like you have the CE Smith boat bunks part #CE27600 in the picture you sent in so then for replacement upright brackets you'd want the #CE27609PG and you'd be set.
Hi Richard; we have no way of knowing what mounting bracket/brakes are on your Load Rite trailer. If you have Dexter/Tie Down Engineering disc brakes with a 9.6" rotor there is a good chance the #DX89UR will fit. However, it is probably best to…
The Dexter Brake Actuator part #099-175-20 replaced the Titan 60 that has a master cylinder with a fitting at the end. The fitting is a 3/16 inverted flare where the brake lines connect to. You do not need an extra fitting when you use the actuator.…
20 year old leaf springs on a trailer could easily stretch 3/4 of an inch. Going with a 25-1/4 inch spring like you mentioned would be great. Since your springs are 3 inch in diameter that would indicate that most likely you have a 5,200 lb axle as…
Yes, the CE Smith Bunk-Style Guide-Ons for Boat Trailers - 60" Long - 1 Pair #CE27600 can work on the inside of a pontoon boat. Based on the photo you may prefer the CE Smith 90-Degree Bunk Board Guide-On Kit #CE27600K90 which will includes…
I do have a solution for you but all of our CE Smith Post-Style Guide-Ons like part #CE27620 have a maximum distance of 13" from the inside of the post to the outside of the trailer frame (see photo). In order to obtain 24" the best option…
The 60" Long CE Smith Post-Style Guide-Ons for Boat Trailers #CE27648 are designed to be installed on I-Beam frames just like you noted in the review video (attached). Some of the review photos you're seeing are from other CE Smith guide-ons…
Dial in a clean, easy-to-spot look with red boat motor accessories that also bring real-world utility. Heavy rubber covers help protect a boat cover and work great to protect the propeller on a trolling motor, and their design should stay on. A simple way to keep gear safer while matching your setup.
Yes, they were exactly as advertised and as described. They work great to protect the propeller on a trolling motor. When it arrives, compare the material and fit to the description and test fit before heading out.
Yes, heavy rubber with a solid design should stay on better than lightweight plastic. A lightweight plastic unit departed the prop on a trip. Check for a snug fit and retention features, and recheck it after your first run or drive.
Yes, it works great to protect the propeller on a trolling motor. It also helps protect the boat cover. The heavy rubber should last a long time. Check that the cover seats fully on the prop and matches your prop size before use.
Yes, it will do what you need to protect the boat cover. The heavy rubber should last a long time. Make sure the prop cover fully shields the blades and that nothing sharp can rub your boat cover.
Filters
