Hey Kris, the Dutton Lainson winch part #DL15440 does not come with a strap so you will need to order one with it. The part #DL24250 will work great with this winch as it is correct width, is 25 feet in length, and has a capacity of 3,700 lb WLL and…
Thanks for reaching out Greg, we get this question from time to time. At this time, we don’t offer any tire and wheel packages in a 5 on 4.25" bolt pattern. The main reason is this bolt pattern's typically is found on a passenger vehicle…
I do not have any exact sizes on the parts used for the Dilly trailer, but fortunately all it takes to figure out the correct parts is a bit of measuring. If you would like to send me the following information, I'll be happy to recommend an axle…
Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…
Jason, you only need one Hub Saver per wheel. Since they're sold in a pack of two, one package is enough for a single-axle trailer with two hubs. If you have a tandem-axle trailer, you'll need two packs to cover all four wheels. The Hub Saver…
It looks like you have the CE Smith boat bunks part #CE27600 in the picture you sent in so then for replacement upright brackets you'd want the #CE27609PG and you'd be set.
Hey Michael, yes the hitches from the 2025 Sprinter fits also fit the 2026 models like the etrailer #e82TR. We haven't carried them over quite yet in our fitguide but we will be soon. What are you planning on using the hitch for?
Hey Jeff, Depending on how much clearance you need from that tailgate is going to determine what kind of hitch extender you will need. Assuming you just have a factory 2" hitch receiver on your Ram you could go with the hitch extender #e48YR…
Hi Richard; we have no way of knowing what mounting bracket/brakes are on your Load Rite trailer. If you have Dexter/Tie Down Engineering disc brakes with a 9.6" rotor there is a good chance the #DX89UR will fit. However, it is probably best to…
The Dexter Brake Actuator part #099-175-20 replaced the Titan 60 that has a master cylinder with a fitting at the end. The fitting is a 3/16 inverted flare where the brake lines connect to. You do not need an extra fitting when you use the actuator.…
Hey, Lance. The direction the springs are in doesn't matter. They can be to the front or to the rear of the axle and will perform the same either way. What kind of trailer are you working on?
Black Boat Motor Accessories for Protection and Security
Black boat motor accessories pair prop protection with security for your setup. Covers stop a trolling motor prop from tearing a boat cover and can shield the blades during trailering, while locks help keep the motor from being 'borrowed'. For a sure fit, choose options for 2-blade or 3-blade props, measure your prop, and check your mounting bolt spacing against lock openings.
Yes, there's a black cover sized for 3-blade props with a 10" diameter. Measure your prop before ordering to ensure the diameter matches. If you also run a 2-blade, select the black dual-prop style that is 12" long to cover that setup too.
Match your mount to the lock's openings: one slot is 4-1/2" wide and the other is 2" wide. Bolt spread can range from 2-1/4" (inside to inside) to 8-3/4" (outside to outside). A proper fit helps deter someone from borrowing your motor. In salt, check the keyway often; some have seen rust and a key that's a little hard to insert. If fit is tight, minor trimming may be needed.
Yes, it helps prevent the boat cover from being ripped by the prop and protects the blades. Position the cover fully over the prop before tightening the boat cover to reduce stress on the blades. It also helps keep lines and hands away from sharp edges around the stern.
Yes, black prop protectors are designed for most 2-blade props. Measure to confirm yours is up to 12" long, 5" wide at the center, and 1" deep. A snug fit helps protect blades and your cover and has kept its stiffness to minimize movement when the motor is running. If your prop is larger than these dimensions, choose a different size.
Boat Motor Accessories Parts or Accessories
Filters
