Measuring for Replacement Axles, Bearings, and Leaf Springs for 1976 Dilly Boat Trailer
Updated 08/18/2017 | Published 08/16/2017 >
Question:
Hi, Im looking to replace the axle, bearings and leaf springs on my 1976 Dilly trailer. the model number for the boat trailer is B-14-15. See pictures attached. What would the correct PNs be?
asked by: Jonathan
Expert Reply:
I do not have any exact sizes on the parts used for the Dilly trailer, but fortunately all it takes to figure out the correct parts is a bit of measuring.
If you would like to send me the following information, I'll be happy to recommend an axle and bearings for you:
-The inner and outer wheel bearings
-The hub face to hub face dimension
-The distance between the spring seats, measured center hole to center hole
-Axle capacity
I've attached an image showing how to measure these parts.
To measure for a leaf spring, you'll want to jack the trailer up so that the axle is hanging freely, then measure directly across from the center of one spring eye to the other. The height of the spring and the distance from the spring eye to the center of the spring can also be helpful in finding the correct replacement. I've attached an image demonstrating how to get these measurements.
Again, if you would like to send me this information, I will be happy to make a specific recommendation for the parts you need. I've also linked you to our product listing for bearings, leaf springs, and axles. In addition, I've included two videos, one on replacing leaf springs on a trailer and the other on replacing both the suspension and the axle.
Product Page this Question was Asked From
Trailer Axle w/ Electric Brakes - Easy Grease - 5 on 4-1/2 Bolt Pattern - 89" Long - 3,500 lbs
- Trailer Axles
- Leaf Spring Suspension
- Standard Grade
- Electric Brakes
- 3500 lbs
- 5 on 4-1/2 Inch
- 74 Inch Spring Center
- 89 Inch Hub Face
- No Drop or Lift
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Kenda 215/60-8 Bias Trailer Tire with 8" Galvanized Wheel - 4 on 4 - Load Range C
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44643 Bearings - Pre-Greased
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - Galvanized
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Search Results: trailer hitch
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer tires and wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Trailer Wiring
- Q&A: Comparing Kenda KR03, KR35, And KR53 Tires
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Shop: Suspension Enhancement
- Shop: Power Mountain Tallboy Off-Road Bottle Jack - 8-1/2" to 37-3/4" Lift - 6 Tons
- Search Results: trailer jack
- Shop: Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness - Dash Knob - Proportional
- Search Results: trailer wiring
- Q&A: Best Suspension Upgrade for 33" Tandem Axles: Road Armor vs Dexter EZ Flex for Ember 22ETS
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Brake Controller
- Search Results: trailer lights
- Article: How to Measure for Trailer Hitch Drop
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: Gooseneck Hitch
- Article: Trailer Lighting Requirements
- Q&A: Instructions to Wire a Trailer for Electric Brakes






