The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…
You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…
Hey Justin, thanks for reaching out! I went out to the warehouse and confirmed that the Curt Adjustable 2-Ball Mount #C79NR measures 12-1/4" from the center of the hitch pin hole to the center of the hitch ball. Not sure what tape measure Curt…
Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
Hey Dewain, we actually have a lock set specifically designed for use with the Bulletproof adjustable ball mount part #BPH77MR with the part #34061674-D. This comes with two locks for the platform of the ball mount and an additional lock for the…
The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…
The ideal height will actually have to do with how tall the coupler of the trailer is from the ground. The Draw-Tite #76020 will sit at 13 1/2 inches from the ground to the top of the hitch when installed on a 2016 Mazda CX-9. From what I could find…
...The maximum drop is 7-inches and maximum rise is 7-1/2 inches. They are adjusted in 1-inch increments.
I went to the warehouse to get the B&W Tow and Stow ball mount # BWTS10049B and provide you a couple...
Hey Sean, yes you can definitely use a stand alone system like a single-acting hydraulic pump to power a hydraulic trailer jack like the single action Stillwell lineup we just started carrying. For the Stillwell Atlas IV 10K Hydraulic Trailer Jack w/…
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…
You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…
Hey Justin, thanks for reaching out! I went out to the warehouse and confirmed that the Curt Adjustable 2-Ball Mount #C79NR measures 12-1/4" from the center of the hitch pin hole to the center of the hitch ball. Not sure what tape measure Curt…
Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
Hey Dewain, we actually have a lock set specifically designed for use with the Bulletproof adjustable ball mount part #BPH77MR with the part #34061674-D. This comes with two locks for the platform of the ball mount and an additional lock for the…
The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…
The ideal height will actually have to do with how tall the coupler of the trailer is from the ground. The Draw-Tite #76020 will sit at 13 1/2 inches from the ground to the top of the hitch when installed on a 2016 Mazda CX-9. From what I could find…
...The maximum drop is 7-inches and maximum rise is 7-1/2 inches. They are adjusted in 1-inch increments.
I went to the warehouse to get the B&W Tow and Stow ball mount # BWTS10049B and provide you a couple...
Hey Sean, yes you can definitely use a stand alone system like a single-acting hydraulic pump to power a hydraulic trailer jack like the single action Stillwell lineup we just started carrying. For the Stillwell Atlas IV 10K Hydraulic Trailer Jack w/…
Experience seamless towing with a 10-inch drop hitch. Perfect for leveling your trailer, it ensures a smooth ride even on bumpy roads. Heavy-duty and easy to adjust, it's ideal for towing tractors or other heavy loads without the jarring 'BANG!' on uneven terrain.
A 10-inch drop is perfect for leveling trailers with higher vehicles, ensuring a smooth, balanced ride. It helps prevent the trailer from tilting, which can cause instability and discomfort during towing. This drop size is ideal for heavy-duty towing, like tractors, providing a relaxed and secure towing experience.
The 10-inch drop hitch reduces the jarring 'BANG!' on bumpy roads by maintaining a level trailer. This alignment minimizes stress on the towing vehicle and trailer, offering a smoother, more comfortable ride. It's especially beneficial for long hauls or when towing heavy equipment.
Yes, a 10-inch drop hitch is designed for easy adjustment, allowing you to quickly set the perfect height for your towing needs. This flexibility ensures that you can adapt to different trailers or loads, making it a versatile choice for various towing scenarios.
A 10-inch drop hitch is built with robust materials to handle substantial weight, making it suitable for towing heavy loads like tractors. Its construction ensures durability and reliability, providing peace of mind that your hitch can withstand the demands of tough towing conditions.
Absolutely, a 10-inch drop hitch is designed to handle rough terrain with ease. Its sturdy build and ability to maintain trailer alignment help absorb shocks and vibrations, ensuring a smooth towing experience even on bumpy roads. This makes it a great choice for off-road or uneven surfaces.
Filters
