1. Wiring
  2. Redline
  3. Tools for Wiring
  4. Wire Clips
Wire Frame Clip

Wire Frame Clip

Item # 464600
lowest price pledge
Our Price: $1.08
Wiring
Orders above $99 qualify for Free Shipping
Shipping Weight: 0.01 lbs
Quantity: 
In Stock
Redline Tools for Wiring - 464600
zoom in icon
slider vertical icon
zoom out icon
Comment field cannot be left empty.
Name field cannot be left empty.

Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.

Error submitting comment. Please try again momentarily.

Product Images

Customer Photos

Videos

Lowest Prices for the best wiring from Redline. Wire Frame Clip part number 464600 can be ordered online at etrailer.com or call 800-298-1624 for expert service.
  • All Info
  • Reviews (120)
  • Q & A (17)
  • Videos (1)
  • Photos
  • Why etrailer?

Redline Wiring - 464600

  • Tools for Wiring
  • Wire Clips
  • Redline


Wire frame clips are made of spring steel with black enamel finish. These clips are used to secure one or more wires to the frame or panel surface.

Specs:

  • Height: 1-1/2"
  • Width: 1/2"
  • Width for wire capacity: 3/8"
  • Frame depth: 5/16"
  • Constructed of spring steel
  • Black enamel finish




Video of Wire Frame Clip

Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.




Video Transcript for Redline Wiring - Tools for Wiring - 464600 Review

Today we're going to be taking a look at part number 464600 this is the wire frame clip. This clip is made of spring steel with a black enamel finish that's going to be used to secure one or more wires to the frame or panel surface of your trailer. You can see right here I have it on piece of angle iron. The piece of iron that I'm using today is going to be a little bit thinner than probably what your trailer frame's made of so it doesn't provide as tight of a fit. This is spring steel, so it's going to fit a variety of widths of trailer frames or panel surfaces and a very versatile clip. It's going to get the job done.

These are going to be designed to hold your wires up and out of the way making sure they don't dangle loose. It's going to help take out any slack in your wiring keeping them up and out of the way, safe and secure from any type of damage or harm. Very simple installation. The overall length is about one and five-eighths of an inch. The width from edge to edge is going to measure about a half inch and then the wire width capacity measuring from inside edge to inside edge is going to measure about three-eights of an inch. I have some 16 gauge bonded wire.

This is going to be wiring for a standard 4-way flat connector. Simply going to place it in there. The clip's going to feature a couple teeth on it. That's really going to help it dig into and hold its place on the trailer frame or panel surface. Once you have your wiring in there, simply just place the clip over the frame and you can see there it gives us plenty of room for our wiring to move.

Albeit it's still going to hold it in place so we don't have to worry about it dangling or very much slack in our wiring, it really cleans up our installation. That's going to do it for our review of part number 464600. This is the wire frame clip. .


Customer Reviews

Wire Frame Clip - 464600

Average Customer Rating:  4.8 out of 5 stars   (120 Customer Reviews)


- 464600
by:

I’m very happy about the product it was very helpful for the project that I was doing it come up perfect fit on my trailer that I have those metal wire clips did the Job that I was expecting to do thank you very much. Gilbert padilla.


Comments
Wonderful
Gilbert - 05/31/2021


- 464600
by:

I haven't used them yet, but they look like they'll do the trick. They're bigger than they look in the photo--and the catalog photo shows the wires on the wrong side (the short side). The wires should be routed under the curved portion on the long side--otherwise the wires could move to the edge of the trailer frame and be pinched. They also look to be a rust magnet, so I'll paint them before installing them.


Comments
Theyre working out wellin a bag in my garage. Theyre way too big for my fairly heavy duty trailer. I tried them and they are too big to snugly pinch the steel frame.
Dave P - 08/25/2015



- 464600
by:

worked great- my trailer has a very thick frame approx 1/4 and these clips worked great to hold the trailer wires intact. Thank You for quick shipping and great product JD


Comments
1 year later and all is well with my clips even after highway driving and some very bumpy red clay roads.Great product
JD - 03/17/2015



- 464600
by:

Two key takeaways here- World class customer service and great products! I did a complete Electric over Hydraulic two axle disc brake setup on my Venture boat trailer. I was basically replacing everything including wiring and coupler. These folks gave excellent support at every turn. Some of the brake lines somehow didn’t make it into the packaging, they jumped through hoops to make it right. Love my new brake system, as I have complete confidence in stopping my boat now.



- 464600
by:

Hi quality for a great price. Overhauled my Boat Trailer rollers, bearings, bunks, wiring and more. I usually shop parts like this on Ebay, Amazon...etc.. Etrailer beat all of their prices, and with free shipping on my $99+ order, the deal got even sweeter. Got my parts in 3 days and had the job done in the next 2 days. All parts fit perfectly and my trailer is like new. This is my second order from etrailer. As we all know it's "always something" with anything marine related. They have earned my business. Thanks..!!



- 464600
by:

Helped support the wiring where the original clips had rusted out. I had to tighten them up by squeezing them with pliers to work properly on the thin metal of my light duty trailer.


Comments
Everything is still working fine.
Rich A - 08/17/2015



- 464600
by:

It would be real nice if this information was put in the product description : The height of this clip is 1-1/2 inches, width is 1/2 inch, width for wire capacity is 3/8 inch and the frame depth is 5/16 of an inch. Constructed of spring steel and has a black enamel finish. These clips are useless for my boat trailer.



- 464600
by:

I could not find these wire frame clips in the local automotive stores nor automotive sections in department stores. Finally I stumbled into them on etrailer. They secure and protect the wire to the metal edge under the trailer. They are designed well providing a nice tight grip holding the wire in place. Shipping was fast. I have since gone through their website exploring their inventory and will order from them again based on my first experience.



- 464600
by:

These clips are perfect. I have an Aluminum boat trailer and every clip I ordered was too small to fit. These are large wire clips and they fit great at a very low price. Service was terrific from e-trailer. Quickly answered my questions and shipped very quickly. Highly recommend them for the personal attention I received.



- 464600
by:

I did an online search for trailer supplies to rework my wiring harness on my trailer. Found etrailer and the online catalog was easy to navigate, the item descriptions were very specific and the prices were reasonable. The user friendliness of the online catalog made it easy to order parts; no guesswork!!!


Comments
The clips are still attached to the trailer and the harness is still in place. No problems with the product!
Craig D - 08/07/2015



- 464600
by:

The best pricing I ever found and shipping is very fast. Great Company to do business with. I plan to order more.



- 464600
by:

The clips are good quality. However I choose not to use them on my boat trailer just because they will rust. I used plastic ty wrap supports. I did use these clips on one of my lowboy trailers.



- 464600
by:

Can't beat the price! Living and having a hitch that is in and out of salt water you need this. Although I have not installed the products that I ordered they are upon inspection out of the box of high quality. I would like to say that this etrailer.com web site and their delivery process is phenomenal. It was delivered promptly and I was kept informed of the order and where it was in the process. Keep up the great job and I will return when looking for item you carry. Thank you.



- 464600
by:

I needed a larger clip for my boat trailer frame than what was offered at the local auto supply chains. These fit the bill. Great product. Highly recommended.



- 464600
by:

This doesn't happen all that often anymore when purchasing items online, but I actually received exactly what I was hoping to get. I have a custom made trailer for my 1959 Tollycraft and when re-wiring the tail lights of course all the wire clips broke. The wire clips that came with my wiring were too small for the thick frame of my trailer. I found the exact type of clip I needed at etrailer at a very reasonable cost and they were delivered in a highly timely manner. I would suggest using etrailer to any of my friends or family.



- 464600
by:

Bought just one to test quality. I'm very pleased with the wire frame clip. You can't find these at your local hardware store...



- 464600
by:

This trailer wire clip works great....it is very secure and does not pop loose....my wires are still secure and in place after over one year of bumping up and down in so many situations. This clip is not flimsy and is rock solid.....great price for what you get



- 464600
by:

This item, (464600), was exactly what I was looking for to hold my new wiring. It was shipped quickly. I had a little confusion about the two different sizes but all turned out well. Great customer service!



- 464600
by:

Exactly as described and a perfect fit. I used them better secure the corrugated plastic sheeting on the bottom of our travel trailer. These clips were used instead of screws to better seal the sheeting to the frame. I also ran some coax cable through the clips to my recently installed rear view camera. Perfect product for the application and appears to have a rust resistant finish.



- 464600
by:

All of the products I have purchased from etrailer have been very useful and quality products the videos of the products are excellent and assuring me of what I am purchasing is going to be right the first time



- 464600
by:

It will hold the wiring, but the end that secures would be better if it was dipped in rubber to insulate against rubbing and shorting out. Ended up using "P" clamps instead.



- 464600
by:

E trailer was quick and low priced. These are the only clips to use don't fool yourself thinking the clips with the light kit will hold. I bought extra to share with people at the boat ramp dragging their wiring out of the water. GET THESE CLIPS FROM E TRAILER.



- 464600
by:

Clips are well made and stay in place on the trailer unlike the cheaper ones I replaced.



- 464600
by:

Great for holding the wire's on the trailer frame and not dragging the ground ! Easy to use . Works great.



- 464600
by:

Good quality light kit. I like the LEDs better than bulbs.


25
121
Show More Reviews

Ask the Experts about this Redline Wiring

  • How does the Wire Frame Clip Attach to an Enclosed or Utility Trailer Frame
    I produced a short video showing how the Wire Frame Clip works on a piece of angle iron. The Principal is the same on a trailer frame and the clip will adhere better to the frame of the trailer because the steel will be thicker. It clips to the trailer or vehicle frame or to a panel edge and secures with an edge that has two points like fangs. The height of this clip is 1-1/2 inches, width is 1/2 inch, width for wire capacity is 3/8 inch and the frame depth is 5/16 of an inch. It...
    view full answer...
  • Suggested Frame Clips to Secure Rubber Brake Lines on Saltwater Boat Trailer
    If your boat trailer has a frame design that will directly accept the clip-in-place Redline # 464600 frame clips then this will be your easiest installation. We do also offer 1/2-inch metal loom clamp # A0500 from Redline that has plated steel construction and a rubber sleeve to prevent friction damage to the wire or tubing secured in it. The enamel-finish clips # 464600 could still be spray-painted with an additional coating of paint for extra protection from corrosion, and this could...
    view full answer...
  • Optomics A12FC Trailer Wiring Harness Clip Kit
    We do indeed still carry the clips as part # CE16867A. They're sold in a quantity of 10.
    view full answer...
  • Frame Clip Size and Styles Available
    The height of the Wire Frame Clip, item # 464600, is 1-1/2 inches, width is 1/2 inch, width for wire capacity is 3/8 inch and the frame depth is 5/16 of an inch. Constructed of spring steel and has a black enamel finish. Metal Looms are also available and we have the 1/2 inch, item # A0500, and the 1/4 inch, item # A0250, which are installed usually with self tapping screws.
    view full answer...
  • Thickness of Metal The Redline Wire Frame Clip Works With.
    The Redline Wire Frame Clip part # 464600 works best metal thicknesses of 5/16" it can go as thin as 1/4" and up to 3/8" in thickness.
    view full answer...
  • Size of Trailer Wire Mounting Clip
    The height of this clip is 1-1/2 inches, width is 1/2 inch, width for wire capacity is 3/8 inch and the frame depth is 5/16 of an inch. Constructed of spring steel and has a black enamel finish.
    view full answer...
  • 7-Way Trailer Wiring Setup Recommendation for a Tandem Axle Trailer
    A 4-way trailer wiring harness wouldn't carry a brake signal so it wouldn't matter how many axles you would have on a trailer that has a 4-way. A better option would be a 7-way as that style of harness does carry the brake signal. Starting with a trailer side 7-Way connector you can use # H20042 which is 3 feet long. It doesn't have to be long though because it is going to the junction box. Speaking of junction boxes you can use # 38656. I have included a picture showing how it...
    view full answer...
    Image 1 for Image 2 for
  • Adding a 7-Way Trailer Connector, Junction Box, and LED Lights to a Trailer
    I think adding a 7-Way and a junction box and not to mention LED lights are great ideas! If you are going to replace all of those items, you may as well go the all out and replace all of the trailer wiring as well. Starting with a trailer side 7-Way connector you can use # H20042 which is 3 feet long. It doesn't have to be long though because it is going to the junction box. Speaking of junction boxes you can use # 38656. I have included a picture showing how it can be wired up and...
    view full answer...
    Image 1 for
  • 7-Way and Junction Box Recommendation for Wiring Trailer for New Lights
    For all the functions you are looking for you would want to install a 7-way and then use a junction box to organize the wiring. Starting with a trailer side 7-Way connector you can use # H20042 which is 3 feet long. It doesn't have to be long though because it is going to the junction box. Speaking of junction boxes you can use # 38656. I have included a picture showing how it can be wired up and a video showing installation to the right. For the rest of the wiring you can use ...
    view full answer...
    Image 1 for
  • Clips and Clamps to Attach Wires and Wiring Harnesses to the Bottom of a Trailer Frame
    There are many ways you can secure wires to a trailer. I would not recommend the use of tape as it will wear out quickly when exposed to the elements. Soldering is also not recommended because it is a more permanent method and you may need to change wires or move them in the future the hot solder would also melt the coating on the wiring, causing a short. If you can find some large enough, wire ties could be a simple solution. We have several clamps and clips that could work for this...
    view full answer...
  • Measurements For Body Chassis and Frame Clips
    We offer a few different frame clips. The Wire Frame Clip Item # 464600 which is 1-1/2" long x 1/2" wide with a 3/8" gap for wiring. We also have the Medium Body Chassis and Frame Clip - Qty 1 Item # SWC9041-1 is 1-11/16" x1/2" with a 1/4" gap and the Large Body Chassis and Frame Clip - Qty 1 Item # SWC9042-1 has the same measurements as the 464600
    view full answer...
  • Recommended Trailer Wiring For 1995 Ranger 690T Boat Trailer
    I did some research and found that your boat is 18-ft 9-inches long. You did not say if your trailer has brakes included which will make a difference when installing the wiring. If you do not have brakes on the trailer and you only need wiring for the lights I recommend part # A35W42B. This is a 35-ft long harness and it has a 4-way flat trailer connector included. This is a wishbone harness that means the running light is split at the connector and the brown running light wire is run...
    view full answer...
  • Availability of Wiring Clips to Attach to I-Beam on EZ Loader Boat Trailer
    The CE Smith Trailer Wiring Clips # CE16867A referenced in your question will fit around edges that are up to 5/32 inches thick. I am not sure how thick the I-beam is on your EZ Loader Boat Trailer but we do have the slightly larger # 464600 Clip that will work with a frame thickness of up to 5/16 of an inch. I recommend simply measuring the thickness on the beam to see if one of these options will work. If the I-beam is too thick for either of these options then your best bet will...
    view full answer...
  • How Thick Can the Metal Be to Use Replacement Wire Clip 027-005-00
    I spoke with a co-worker who has used clip # 027-005-00 and he recommends attaching it to metal no thicker than 1/4 inch but that it might work with 3/8 inch thick metal. A better option would be # 464600 since it is a little larger and meant for this application more than the other clip. Another option is to use a loom clamp such as # A0250. I have included a link to a video review featuring this clamp for you.
    view full answer...
  • Wire Loom Clamp/Clip Recommendations for 4-Way Wiring.
    Based on our customer reviews it looks like the Wire Frame Clip # CE16867A that you referenced has better reviews than the Wire Frame Clip # 464600. Either one should work fine, but if it were me I would go with the # CE16867A between those two. Another option is the Metal Loom Clamp # A0500. You will need to provide some self tapping screws but this is the loom clamp that our installers here at etrailer use the most. These clamps are rubber coated to protect the wires and since they...
    view full answer...
  • Parts Needed to Install New 7-Way and Wiring on a Trailer
    Starting with a trailer side 7-Way connector you can use # H20042 which is 3 feet long. It doesn't have to be long though because it is going to the junction box. Speaking of junction boxes you can use # 38656. I have included a picture showing how it can be wired up and a video showing installation to the right. For the rest of the wiring you can use # DW04914-1 which is sold by the foot. So if you needed 20 feet you would enter 20 into the quantity box. And for ring terminals you...
    view full answer...
    Image 1 for
  • Wiring and Accessories Needed to Add Backup Lights to a Boat Trailer
    You are going to want to run a separate wire from the new back up light(s) to the trailer connector. Depending on the type of trailer connector is on the trailer and on the vehicle you may need different connectors or adapters which I can help with. I just need to know the type of connector on the trailer and tow vehicle. For wire you can use # 16-1-1 which is sold in increments of 1 foot. So it you needed 20 feet you would enter 20 in the quantity box. I also recommend using wire...
    view full answer...




  • Why etrailer.com?

    At etrailer.com we guarantee:
  • Highest quality wiring for the best price.

    Our Lowest Price Pledge ensures you will never overpay for the parts you need.
  • Real product know-how.

    We make sure that the products we sell are what we say they are, and that they work the way they are supposed to work. Get real advice from a real person who has the knowledge and expertise needed to solve your problem.
  • Most detailed, accurate wiring information available.

    Because we take providing accurate product information seriously, we take our own detailed product photos, demo videos and installation videos, as well as verify measurements, instructions, and vehicle fit information.
  • Installations, made easy.

    We love helping people and have the most highly-trained customer service, hands-on experience, step by step videos and installation instructions.
  • Fast shipping.

    Your order is automatically routed to get out of our warehouse and to your door as quickly as possible. Receive free shipping on orders over $99.
  • Personalized service for life.

    We provide one-on-one, personalized service from the ordering process through the life of your product.
  • Trusted since 1946.

    We've been serving customers since our parts store first opened in 1946 and continue to be recognized by our customers, our vendors and third parties for exceptional service.
  • Returns Policy

    Need to return an item? No problem. Please read our Returns Policy for more information.

Info for this part was:

Employee Robert G
Expert Research:
Robert G
Employee Cole B
Installed by:
Cole B

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.