Deka Ring Terminal - Heat Shrink - 16-14 Gauge - 1/4" Ring ID - Nylon Insulation - Blue - Qty 1
(9 reviews)
Price: $1.83
Deka Ring Terminal - Heat Shrink - 16-14 Gauge - 1/4" Ring ID - Nylon Insulation - Blue - Qty 1
Item # DW05737-1
Our Price: $1.83
- All Info
- Reviews (9)
- Q & A (0)
- Videos (1)
- Photos
Deka Wiring - DW05737-1
- Wire Connectors
- Ring Terminals
- 16-14 Gauge
- Deka
- 1/4 Inch Diameter
This blue ring terminal fits 16-14 gauge wire and has a 1/4" ring inner diameter. Insulated with heat-shrinkable nylon for adjustability and durability.
Features:
- Fits 16-14 gauge wire
- 1/4" Ring inner diameter
- Heat-shrinkable nylon insulation allows for adjustability and provides durability
- Blue
- Quantity: 1
- 1-Year limited warranty
38313 Ring Terminal - Heat Shrink - 16-14 Gauge - 1/4 Inch Ring Inner Diameter - Qty 1
Replaces 05737
Video of Deka Ring Terminal - Heat Shrink - 16-14 Gauge - 1/4" Ring ID - Nylon Insulation - Blue - Qty 1
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Deka Heat Shrink Ring Terminal Review
Speaker 1: Today we're going to be taking a look at the Deka quarter-inch heat shrink ring terminal for 16 to 14 gauge wire. That's going to be part number DW05737-1. Our heat shrink ring terminal is going to keep out all of that moisture and debris that could potentially cause corrosion build-up inside the connector. It's going to be especially useful in applications, like this, where it's going to be on the outside of either a vehicle or a trailer, where it's going to be exposed to the elements. It's also going to come in handy if you have a boat trailer, where it's going to be near a lot of water.Because, unlike traditional style ring terminals, it's going to be sealed at the back. Whereas with the other one, it's going to have an opening and potentially having a opening at the front.
Where we're going to have wires really close to that ring. Where it could, again, get that moisture in there and cause a lot of corrosion. A ring terminal is going to work with 14 to 16 gauge wire. And the ring, itself, is going to be a quarter-inch inner diameter. It's going to be perfect for those ground wires with the self-tapping screw, or any other small terminal that you can fit a quarter-inch ring around.The heat shrink is going to be a nylon.
If you just take some heat and apply it to it, it will shrink right around that wire and give it that extra durable coating, but also still be flexible enough that we can move the wire around and not have to worry about it breaking, or moving it around inside the terminal. We're going to be using our ring terminal for our ground wire coming out of our junction box on our trailer. We already have a hole drilled, so we're just going to measure out about how much wire we're going to need. It doesn't hurt to give yourself a little bit of extra. We'll cut off the excess and we'll strip back the end of the wire.We'll take our ring terminal, slide the bare wire in, and crimp it in place.
Just need to apply some heat, so we can shrink down that connector. We're going to be using a heat gun. That way I don't have to worry about it charring or burning the connector or the wires. We'll taking a self-tapping screw, put it loosely in place, and come back with a nut driver and tighten it up.That will finish up your look at the Deka quarter-inch heat shrink ring terminal, part number DW05737-1.
Customer Satisfaction Score:
96% were satisfied with this product
4% of customers were not satisfied
- etrailer mistake
- Did not arrive in time
Customer Reviews
Deka Ring Terminal - Heat Shrink - 16-14 Gauge - 1/4" Ring ID - Nylon Insulation - Blue - Qty 1 - DW05737-1
Average Customer Rating: 4.8 out of 5 stars (9 Customer Reviews)
This blue ring terminal fits 16-14 gauge wire and has a 1/4" ring inner diameter. Insulated with heat-shrinkable nylon for adjustability and durability.by: rewire novice11/23/2016
Worth the money compared to the cheap hard-plastic versions...especially for marine applications. Suggest to still use shrink tubing on top of the heat shrink on the ring terminal...slide a piece of shrink tubing onto the wire, heat/shrink down the terminal first, then slide down your tubing and shrink on top of everything for a lasting connection.
by: Bruce04/29/2017
Order was complete and delivered in a timely manner. Only problem (minor) was the 7way pigtail was not wired to color code. Had to use test light to get 3 of the wires in correct location. Could be a problem if someone wasn't comfortable with ringing out wires.
by: Scott09/04/2015
I ordered multiple items from etrailer and the experience was perfect. The products arrived exactly as described with super fast shipping (standard option). The communication was frequent and thorough. This company knows good customer service. I didn't have any issues, but don't have any worries with this company if any come up.
by: Mel M08/24/2015
Got my brakes and hubs on and they are great. Best price I could find and glad these guy are doing such a good job. No parts missing... now that's the ticket. Would recommend them any time.
by: Patrick05/31/2018
excellent product ,easy to install
by: Walt 04/08/2020
Great
by: Jim11/04/2017
Delivered fast and worked perfectly!
by: twink02/08/2016
great
by: Andy 04/16/2021
9
9
See what our Experts say about this Deka Wiring
- What Is Ring Inside Diameter Of 16-14 Gauge Ring TerminalThe inside diameter of a 16-14 gauge ring terminal ring like part # DW05737-1 is 1/4 inch.
view full answer... - How to Create a Better Ground for a Clearance Light on a TrailerSince you have already determined that it is a ground issue (which is almost always the problem) I would try sanding down the area you are installing the clearance light on. A good ground will have a solid connection to a clean, bare metal surface. If the screws are loose (as you found) or the metal has some paint or debris on it there could be some issues. If that doesn't work you can also try using a ring terminal like part # DW05737-1 and some 16 Gauge Wire # 16-1-1 to create a better...
view full answer... - Troubleshooting Vehicle 4-way Connector Having No Ground When Plugged Into TrailerSince the ground issue on the 4-way connector on your vehicle only occurs when the trailer is plugged in, it sounds like the trailer ground is bad. First I would make sure that the main ground to the tongue of the trailer from your new 4-way connector is secure to clean corrosion free metal. Next if your trailer has an aluminum frame or a tilt bed you will likely need to run jumper wires from the mounting hardware of each light to the main ground on the tongue, as these style trailers...
view full answer... - How To Install Cab Lights On The Roof Of A 1985 Chevrolet C/K Series Pickup Truck We have a variety of roof mounted cab lights for your 1985 Custom Deluxe. Although there are many different types, the majority of them will have the same installation method/instructions. The Clearance Light Kit part # CB-15AK has everything you will need to install cab lights on your truck. The first thing you will want to do is disconnect your vehicle's battery. You will then want to use the cab lights to mark out the position on the roof where you want the lights to sit. After this...
view full answer... - Comparing How To Wire Single Wire and Two Wire LED Lights In Box Truck2 wire LED lights and single wire LED lights will get wired pretty similarly. On a single wire light like the Optronics LED Trailer Clearance and Side Marker Light w/ Reflex Reflector - 6 Diodes - Amber Lens # MCL44AB1 you were looking at the wire is for power, and the light is grounded through the mounting hardware. On a 2 wire LED light like the 60" LED Lights you have the white wire will get grounded to your box truck, and the other wire is the power wire. You will need to make sure...
view full answer... - Wiring Connections For Bright Way Push-to-Test ICU Trailer Breakaway Kit # BW94FR I have added an image below for the Bright Way Push-to-Test ICU Trailer Breakaway Kit # BW94FR as well as an installation video that is also very helpful. Here is where all the wires will connect from both the battery box and the breakaway switch. Battery Box White- Ground Wire(white) Red- 12 Volt Charge Line(red or black wire) Blue- Breakaway Blue Wire Black- Running Lights(brown wire) Breakaway Blue- Battery Box Blue Wire Black- Trailer Brake Wire(blue or black wire) Four of the...
view full answer...
- Recommended License Plate Light To Replace Obsolete Wesbar Light on 2003 Ranger Trailer Boat TrailerIt appears your lights are obsolete from Wesbar. As I was unable to find your exact lights you might consider the LED Trailer License Plate Light # LPL82CBB. This light is submersible, mounts with studs and the LED lights are very bright. This light uses a 2 wire connection which you can add a Ring Terminal # DW05737-1 to connect the ground to one of the mounting studs so you only need to connect your power wire.
view full answer... - Replacement Ring Terminal for Curt Trailer Wiring Harness # C99DRFor a replacement ring terminal to use with the Curt wiring kit part # C99DR you'd want the part # DW05737-1 and you'd be set.
view full answer... - How to Connect 5 Wires on Trailer to 4-Way ConnectorFor your application I recommend picking up the Wesbar Wishbone Wiring Harness with 4-Pole Flat Trailer Connector # 002402 because it has the 2 brown wires so your installation will be really simple. Just use heat shrink butt connectors like part # DW05743-5 for the standard wires and add a ring terminal like part # DW05737-1 for the ground wire. If you already have a 4-Way connector with just 4 wires then you'll combine the ends of the 2 brown wires and connect them to the running light...
view full answer... - How to Install the On/Off Switch Panel for Atwood Gas and Electric Water Heaters Part # AT91230I have attached the wiring diagram for the Replacement Double-Panel On/Off Switch for Atwood Gas and Electric Combination Water Heaters part # AT91230. The installation will be very simply with only 5 connections needed. There will be three terminals that go to the water heater (orange, blue, white), one terminal that goes to a 12 volt power source, and one terminal that goes to a ground. In order to make these connections I recommend using four of the Female Spade Terminal Quick-Disconnect...
view full answer...
- Installation of Dual Switch on Suburban Brand Water HeaterYou can absolutely install a double switch like the Replacement Double-Panel On/Off Switch for Atwood Gas and Electric Combination Water Heaters - White # AT91230 on your Suburban Water Heater. This switch when wired correctly will allow you to power the gas burner and electric components independently. I've attached a wiring diagram to assist. You may want to use the Female Spade Terminal Quick-Disconnect # DW01899-1, butt connectors # DW05743-5, and Deka Ring Terminals # DW05737-1.
view full answer...
- Replacement 7-Way Trailer Connector with Wiring for a 2007 Sportsman TrailerFor you I recommend the Trailer Wiring 7-Way Upgrade Kit # e99011. This comes with an 8 foot 7-Way connector, wire loom, a junction box, and ring terminals. Everything you need to install a 7-Way. The junction box makes troubleshooting lighting and other problems much easier. If you already have a junction box then you can use # H20044 and just use ring terminals. You would need 4 of # DW05737-1 and 3 of # DW05740-1. I have also included some links on testing and troubleshooting brake...
view full answer... - Hazards Turn on 2012 Ford Explorer When Headlights on RV are Turned onIt sounds like your ground could be the problem in this situation. The Ground wire on the Blue Ox Tow Bar Wiring Kit # BX8848 needs to be run to a main Ground or installed directly to a clean, bare metal surface on the chassis of your 2012 Ford Explorer. If you ran the white Ground wire from your 4-Way to the tail lights then you could possibly be getting some residual signal which could be causing your hazard lights to flash. Go ahead and disconnect the Ground wire and Ground it to see...
view full answer... - Wiring An Atwood RV Water Heater With Double-Panel On/Off SwitchThe manual for the Double-Panel On/Off Switch for Dometic Gas / Electric Combination Water Heaters - White # AT91230 lists the wire as orange but the manual for Atwood water heaters like AT94022 list the wire as red. It's referring to the wires that come out of the top of the unit. The three dash symbol you're referring to means ground. The blue wire will connect to terminal 6 of the switch. Terminal 4 of the switch will go to the negative battery terminal. The green wire will connect...
view full answer...
- How To Mount the Optronics LED Clearance or Side Marker Light w/ Reflex Reflector Part # MCL31ABThe Optronics LED Clearance or Side Marker Light w/ Reflex Reflector part # MCL31AB mounts by running two screws like part # 1131832 though the base. In order to access these screw holes you will need to remove the lens. I have attached a photo that shows the screw holes. I have also attached an install video for you as well. In order to make the wiring connections you will also need part # DW05714 and part # DW05737-1.
view full answer...
- Noco Genius Gen 3 10amps x 3 tank Wire ExtensionThe NOCO Genius Gen3 already has the fuse on each line and they don't have the extensions available for this model. You can extend the wires, but if you alter your wiring, you will void your warranty. You only need to extend the wires and put the ring terminals on either end to give yourself a working solution. I recommend using wiring # 16-1-1, and ring terminals # DW05737-1. You will simply use a bolt and nut to connect the two wires...but make sure the negative and positive wires...
view full answer... - Ground Wire for Ceiling Light on Old Camper with Only a 12V Battery SystemTo wire the RV Euro Style Interior Double Ceiling Light with Built-In Switch # RVIL22 to your old camper with 12V battery system, you will simply connect the black wire to 12V power, and then the white wire will connect to any metal that is in some way attached to your trailer frame. You will want to use a self-tapping screw like # FA1131822 along with a ring terminal like # DW05737-1. I recommend connecting your 12V power and testing the ground location before tapping to ensure function....
view full answer... - How to Ground a Trailer LightI was not able to reference the tow smart light kits you are referring to but a trailer taillight will ground one of two ways. They can either ground using a single wire (usually white) or through the mounting hardware. If they ground using a single wire then that wire will need to be attached to a bare metal part of the trailer frame with a screw like part # FA1131822 and a ring terminal like part # DW05737-1. If there is any paint on the ground location then you will need to sand it down...
view full answer... - Running Wiring For Bully Light Bar At Back Of 40-Ft Fifth Wheel TrailerThere are a couple of ways you can run the wires for the Bully Light Bar, part # BLS-1103. The easiest way would be to attach the light bar wiring to the wiring you have at the rear of your fifth wheel trailer. That is if you can access the wiring easy enough either by getting to the wires under your trailer or by removing the lights and getting to the wiring behind them. Another way would be to install a junction box like part # 38656 on your fifth wheel and attach the trailer wiring...
view full answer... - Replacement 4-Way Trailer Connector and Ground WireThe white wire on a 4-way trailer connector is usually for the ground. The reason your lights are not working is because this connection is severed. If you cannot re-attach the wire using a butt connector like part # DW05744-5 then you can replace the 4-way with part # HM48192. If a new ground wire needs to be ran you can use part # DW02359-1 (per foot), part # DW05737-1, and part # FA1131822. The ring terminal will need to be attached to a bare metal surface free of paint. I have attached...
view full answer... - Splicing Two 3040-P Brake Controller Wiring Adapters Together to Reach Brake ControllerAll you'll need to do is get a length of 16 gauge primary wire, part # DW02359-1 (sold by the foot) and use a butt connector like # DW05744-5 and a ring connector like # DW05737-1. Simply cut the white wire with the ring terminal and use butt connectors to splice in the length of wire. You'll also need butt connectors to connect the two # 3040-P wiring adapters together. The blue and black wires are 12 gauge and the red and white wires are 16 gauge. You'll have extra connectors from the...
view full answer... - Installation of Trailer Wiring # 16-4B-1 Where Will the White Wire Go?The white wire on the # 16-4B-1 bonded wire,is the ground wire. You will want to secure it to a clean metal surface that touches the trailer frame. It is often secured with a ring terminal like # DW05737-1 and screw # FA1131822. I have linked the above mentioned products as well as a Help Article to this page for your viewing and purchasing convenience.
view full answer... - Replacing 2 Wire Marker Lights With Single Wire Marker LightsOn lights similar to the Optronics LED Trailer Clearance and Side Marker Light # MCL44AB1 that will only have 1 wire pigtail this is the positive power wire. The light requires mounting to a grounded metal surface that will provide you the ground connection. If you are not able to attach it to a grounded metal surface you can also use a jumper Wire # DW02359-1 with a Ring Terminal # DW05737-1 to attach to your existing wiring or a nearby grounded surface. There are some lights similar...
view full answer... - Installing A Light Run Off A Toggle SwitchThe Bully Bumper Mount Backup Light - Clamp On # PL-807 can be added to a switch on or near your dash. I recommend using the Pollak Light-Duty Toggle Switch - On-Off - 12 Volt - 10 Amp - 6" Wire Leads # PK34513 and running wire directly from your battery for power using a ring terminal like # DW05737-1. You can use butt connectors like # DW05744-10 and wire by the foot like # 16-1-1. This will allow you to use the light at any time whether the car is on or off.
view full answer...
Do you have a question about this Wiring?
Info for this part was:
Updated by:
Adele M
Updated by:
Wilson B
Video Edited:
Kathleen M
Written by:
Laura H
Expert Research:
Jeffrey L
Installed by:
Robert C
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.