See what our Experts say about this Deka Wiring

• Installing a Brake Controller on a 2016 Honda Odyssey
  The parts needed and steps taken to install a brake controller, like the Tekonsha Prodigy P3 # 90195, on your 2016 Honda Odyssey will really depend on what they are wiring for your 7-Way. If they have wired all of the functions then you will simply need to connect the 4 wires from the pigtail on the P3 to the following functions: White - Ground (negative terminal on battery) Red - COLD side of Stop Light Switch (wire that gets hot only when brake pedal is pressed) Black - 12V Power (positive...
  view full answer...
  
• How To Run Grounds for Lights on an Aluminum Frame Trailer
  It sounds like you may be wondering how to attach the grounds on your trailer because it has an aluminum frame which you have either read or experienced issues with. If that is the case then I recommend you first use a junction box like the Pollak 10-Terminal Junction Box part # PK52248. Once you have this you can then run all of your lights and trailer connector to a single ground point on the coupler with a ring terminal like the part # DW05762-1 (junction box to coupler) and extra wire...
  view full answer...
• Wiring Diagram for the HydraStar Electric Over Hydraulic Actuator for Drum Brakes Part # HBA-12
  I have attached a photo that shows the wiring schematics of the HydraStar Electric Over Hydraulic Actuator for Drum Brakes part # HBA-12 for you. If you need any wiring connectors then you can use part # DW05745-10 and part # DW05762-1. These connectors have a heat-shrink housing which will help to keep out water and prevent wiring malfunctions.
  view full answer...
  
• Replacement Trailer Brakes For 2000 Damon Camplite Pop-Up Camper With AL-KO 8440 7" Drum Brakes
  Your AL-KO 8440 drum tells me you have a 7" brake drum with a 5 on 4-1/2" bolt pattern. This will need 4 of the Easy Grease Trailer Hub and Drum Assembly # AKHD-545-2-EZ-2K if you are needing to replace the drums themselves. For the brake assemblies you will need 2 of the Brake Kits # AKEBRK-2. We do have the Mounting Hardware # BRKH7 for the brake assemblies as your hardware may not be in the best condition with the age of the 2000 Damon Camplite pop up camper. We have 12 Gauge Wire...
  view full answer...
• Parts Needed To Add Curt Echo Trailer Brake Controller To a 2022 Toyota RAV4 With Factory 4-Way
  As you already have the Curt Trailer Connector Adapter # C57672 to connect to the 4-way on your 2022 Toyota RAV4, the Curt Echo Wireless Trailer Brake Controller # C51180 only requires an additional charge line to be ran. For this you will need some 10 Gauge Wire # 10-1-1 to run to the battery. This wire is sold per foot so be sure to get enough for routing safely and away from rotating parts or exhaust to prevent damage to the wire. Cable Ties # DW05724-25 will work well to secure the...
  view full answer...
• Trailer Lights Go Out When Headlights and Brake Pedal are Applied
  The problem you described sounds like a ground issue. What I recommend doing is running the ground wire for each of the trailer lights (assuming they do not all ground through the mounting hardware) up to the ground used for the 4-way trailer connector. I would then reground the bundle of wires for the lights and connector to a new bare metal spot on the trailer frame using both a self tapping screw like part # FA1131822 and ring terminal like part # DW05762-1. If you need additional wire...
  view full answer...
• Wiring Required To Use a Curt Echo With A 2020 Honda Odyssey That Has Factory 4-Way Flat Connector
  For The Curt Echo # C51180 to function it must have power from the charge line of the 7-way and signal from the brake lights. The Curt Trailer Connector Adapter # C57672 sounds similar to the connector that you added to your 2020 Honda Odyssey. The 4-way takes care of the light signals that the Echo needs to see. You will need to run a 10 Gauge Wire # DW02508-1(this is sold by the foot so be sure to measure how much you will need) to your battery with a 30 amp. In-Line Circuit Breaker...
  view full answer...
• Trailer Wiring Harness Adapter to Convert 4-Pole to 7-Way to Allow Charging Trailer Battery
  To convert your Sienna's flat 4-pole trailer connector to a round 7-way RV-style that includes a circuit for charging a trailer battery you will use Hopkins part # 37185. This simply plugs in to your existing 4-pole and will then carry the same lighting signals. In order to have a 12V charging circuit active on the 7-way you will need to add a connection for that new circuit. You will also need 10-gauge wire, part # 10-1-1; a 40-amp circuit breaker, part # 9510; as well as ring terminals...
  view full answer...
  
• What To Do When Your 7-way Ground Wire Isn't Reaching The Frame
  Hi Burhan, You can cut off the ring terminal and splice on some additional 10awg wire # 10-1-1 using a heat shrink butt connector # DW05745-5 to get the correct length to reach the frame. You can then crimp on another ring terminal # DW05762-1 and use a self-tapping screw to attach it to the frame.
  view full answer...
• Parts Needed to Install Curt Echo In-Line Brake Controller on a 2001 Roadmaster Monaco Motorhome
  Hey Rick, I definitely get your hesitation on running wiring from the back of your 2001 Roadmaster Monaco, but since you currently only have a 4-Way connector installed we'll have to route wiring at least from your battery back to the wiring connector to power the Curt Echo In-Line # C79DR. There are other brake controller options out there but they either require the 12V power like the Echo In-Line, or they also require routing wiring into the cab of your motorhome so the In-Line will...
  view full answer...
• Wiring Needed To Attach a Charge Line On The Motorhome When Flat Towing a Vehicle
  Since you are running 50' of wiring you will want to use 10 Gauge Wire # 10-1-1 which we sell by the foot. Roadmaster has their Battery Charge Line Kit for Motorhomes # RM-156-75 which only comes with 30' of 12 gauge wire. You can build a similar kit with the wiring, Circuit Breaker # PK54220PL, two 10 gauge Deka Ring Terminals # DW05762-1 to connect to the circuit breaker, a 3/8" Ring Terminal # DW05741-1 for connecting to the battery and some Wire Loom # 7509-1 to protect the wire under...
  view full answer...

Do you have a question about this Wiring?