See what our Experts say about this Optronics Trailer Lights

• Taillight Recommendation for F008585-2 Fulton Trailer Fender
  We don't offer a taillight specifically designed for use with the # F008585-2 fenders you'd looked at, but I've seen folks use taillights like the # STL78RB mounted to the rear of the fender step as shown in the provided photo. You'd then need to devise a way of mounting and illuminating the license plate if you were to go that route. You could bend a slight radius on the license plate and actually mount it vertically to the rear face of the fender as shown in the provided photo. You'd...
  view full answer...
  
• Installing Optronics LED License Plate Light # LPL31CB
  Trailers are usually wired so that the brown wire carries the running light circuit. The wire color on the wiring system of a vehicle can vary. You can easily find the correct circuit by turning the vehicle running lamps on and then using a circuit tester like part # PTW2993 to test the wires feeding the taillight assembly until you find the wire that shows current. The # LPL31CB lamp has two wire leads, one would tap into the running light circuit, the other would tap into an existing...
  view full answer...
• Replacement License Plate Light For 2009 Haulmark 7x12 Low Hauler Trailer
  I did some research on your 2009 Haulmark Low Hauler trailer. I was able to see several different styles of license plate lights and holders on trailers. I have attached a link to our product page for license plate lights. Some have the license plate holder attached to the assembly and some are just the lights that are mounted to light the license plate. There are different opinions about mixing LED and incandescent lights on the same circuit. We have had customers that wire them in the...
  view full answer...
• How Many Trailer License Plate Lights are Required On a Trailer
  You should only need one license plate light like the part # LPL31CB to be legal as long as it properly illuminates your license plate. I attached a couple review videos for this light plus a help article on trailer lighting requirements for you to check out as well.
  view full answer...
• Finding Wire for Adding License Plate Light on Motorcycle
  Finding a running light wire on trailer wiring for adding a license plate light typically is a matter or tapping into the running light circuit on trailer wiring. While we do have install videos on trailers we don't typically do them on motorcycles for trailer wiring as that's not what these were designed for. And we don't get a lot of requests here to install trailer lighting on motorcycles. The best solution I can recommend would be to trace the wiring that runs to the running light...
  view full answer...
• What Size are the Mounting Holes for LED Mini Trailer License Plate Light # LPL31CB
  I went out to the warehouse and pulled LED Mini Trailer License Plate Light # LPL31CB to take some measurements for you. This light does include some screws to mount it. The screw holes are approximately 3/16 inches in diameter. I made a video for you showing the dimensions for you. The wires coming out of the back are coming out of a couple of round nubs. The overall dimensions of the nubs (the hole size to cut if needed) would need to be 1/2 inch across by 1/4 inch tall.
  view full answer...
• Is LED Mini Trailer License Plate Light DOT Compliant?
  According to Optronics, you will need a pair of LED Mini Trailer License Plate Lights # LPL31CB, mounted on each side, in order for it to be DOT compliant.
  view full answer...
• Replacement Trailer License Light Recommendation
  We have several license plate lights available (see link), but I would say the closest one we offer to the one in your picture would be the # LPL31CB.
  view full answer...
  
• Steel Frame License Plate Bracket Availability that is Compatible with LED License Plate Light
  If you dont mind drilling a few holes you could get the LED Mini Trailer License Plate Light # LPL31CB to work with a Steel Trailer License Plate Mount Bracket # LP20SB. But I pulled both these products from our warehouse and the holes of these products do not line up, but if you used the # LPL31CB as a template you could drill the correct dimension holes in the # LP20SB above its current holes. Or you could check out the Optronics Heavy Duty License Plate Bracket # LP15SB. This has a...
  view full answer...
• Is the Optronis License Plate Light Bracket Flat
  The Optronics License Plate Light Bracket # BK31BB is a flat bracket. This bracket is designed to work with either the Optronices Mini Trailer License Plate Light # LP31CB or the LED version # LPL31CB
  view full answer...
• Could LED Mini Utility Light be Used as License Plate Light
  You said your license plate mount bracket is recessed so as long as the light part # UCL13C2PG can be mounted pointing down towards the plate it would work well for you. If you were to mount it on the same vertical wall as where the license plate is the light would be directed towards the back of the trailer and would not work well. If you need something to mount directly over the plate you would need the part # LPL31CB.
  view full answer...
• LED License Plate Light for a 2007 Triton Elite 101x20 Trailer
  We only have 3 clear lens, white light LED lights for license plates. First is # LPL31CB. I have included a link to a video review of it for you. We also have # LPL41CB which will be brighter because it has 5 diodes. And then there is LED light with bracket, # LPL55CB.
  view full answer...
• Dimensions and Recommended Mounting Hardware for the LED Mini Trailer License Plate Light
  The LED Mini Trailer License Plate Light # LPL31CB comes with installation screws, but if needed you could install it with other hardware. You might find that a self-tapping screw would work better if you plan on installing this to a metal surface. The distance on center between the mounting holes is 2 inches. The diameter of the holes is 3/16 of an inch. And the thickness at the mounting holes is an 1/8 of an inch.
  view full answer...
• Recommended Tail Lights And LED License Plat Light
  The Bargman LED Triple Trailer Tail Light - 4 Function - 36 Diodes - Black Base - Red, Amber, and Clear Lens Item # 47-84-005 is a recessed light and doesn't have a license plate light. There is nothing with this style or size that does. I recommend using a separate light like the LED Mini Trailer License Plate Light, 2 Diode - Chrome Plated # LPL31CB for this. You can also use a frame and LED combination like the LED Trailer License-Plate Light w/ Mounting Bracket, 2 Wire, 5 Diode -...
  view full answer...
• Instructions for Wiring Additional License Plate Light With Submersible Trailer Light Kit # TL5RK
  When it comes to adding an additional license plate light to the Submersible, Under 80" Trailer Light Kit with 25' Wiring Harness, # TL5RK, I recommend taking a look at the LED Mini Trailer License Plate Light, # LPL31CB. The light has a weathertight seal to protect it against the elements and the two-wire design includes the lead and ground wires to mount to any surface. In order to wire this light, one of the wires will need to connected/spliced into the running light circuit (brown...
  view full answer...
• Availability of a License Plate Light that is Made in the U.S.A.
  I went out to the warehouse and pulled Peterson license plate light # M439K. The packaging does indicate that it is made in the USA. I have included a link to a video review of the light for you.
  view full answer...
• Can Optronics LED Mini License Plate Light # LPL31CB Mount Upside Down Without Water Leakage
  The light you referenced, Optronics LED Mini License Plate Light # LPL31CB, is intended to mount so that its chrome-finish cover is on top. Although it does have a weathertight seal against the elements, this is intended to provide protection from water damage in the usual mounting position. I recommend one of the lights shown on the linked page since these products are all submersible. None of these happens to be an LED-type however. Optronics # LP91CB can be used along with their bracket...
  view full answer...
• Do Tail Lights on GearDeck 17 Enclosed Cargo Carrier # H00604 have a License Plate Light
  I went out to our demo area and personally checked the lights on the GearDeck 17 Enclosed Cargo Carrier # H00604. While there isn't a specific white light that shines down on the license plate the red lights for the other functions do illuminate that area slightly so the license plate would not be complete in the dark at night. For greater visibility you could splice in an LED license plate light, # LPL31CB, and be in compliance for sure.
  view full answer...
• Is the Bargman Surface Mount LED Double Tail Light Available with an Integrated License Plate Light
  At this time there is not a version of the Bargman LED, Surface Mount, Double Tail Light, # 47-84-610, that incorporates a license plate light at the bottom of the housing. We do have a solution for you though. You could install the Bargman lights that you like and then install an LED license plate light like the LED Heavy Duty Trailer License Plate Light, # LPL41CB, or the LED Mini Trailer License Plate Light, # LPL31CB, above your license plate. If you need a bracket to attach the license...
  view full answer...
• Recommended Metal License Plate Bracket with Light
  For a metal license plate bracket with light, we have the Peterson License Plate Light with Bracket # PM436B. We have other options with lights but they are a polymer. You can always get the parts separately like bracket # LP20SB, # CE26053A or # LP15SB and then add the light # LPL31CB. I've attached a link to your light options.
  view full answer...
• License Plate Recommendation for a Small Trailer Towed by Motorcycle
  Most likely yes, but you would have to check with your local DOT to confirm that. An easy light to use would be the part # LPL31CB. This would tie into the running light circuit of the trailer's lights and would light up the license plate.
  view full answer...
• Recommendations for a Vehicle with all Blinkers Converted to LEDs
  There are work arounds that allow you to install LEDs in the place of blinker bulbs. For example you can install a load resistor like our LED Light Bulb Load-Resistor Kit # DI34ZR on each light assembly that will blink with the turn signals. However, since you plan on replacing all your blinkers with LEDs I thing you would be better off going to an electronic flasher relay to replace the thermal one in your vehicle. Currently none of the LED lights we offer have pre-installed load resistors. This...
  view full answer...
• Availability of LED License Plate Lights
  We do have some LED license plate lights. You could use # LPL31CB or # LPL41CB. I have included some links to video reviews for each of these lights for you.
  view full answer...

Do you have a question about this Trailer Light?