1. Trailer Hitch
  2. Draw-Tite
  3. Class III
  4. 2 Inch Hitch
  5. 4000 lbs GTW
  6. Concealed Cross Tube
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"

Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"

Item # 75992
lowest price pledge
Retail:$202.38
Our Price: $123.31
You Save: $79.07
Trailer Hitch

Will this fit?

To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.

This item qualifies for Free Shipping
Shipping Weight: 32 lbs
Quantity: 
In Stock, Ships Today
Trailer Hitch 75992 - Class III - Draw-Tite
zoom in icon
zoom out icon
Comment field cannot be left empty.
Name field cannot be left empty.

Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.

Error submitting comment. Please try again momentarily.

Product Images

In Use/Installed

Customer Photos

Fully welded vehicle trailer hitch is strong and durable. Draw-Tite's Tested Tough guarantee ensures that this hitch exceeds industry standards. The combination of an e-coat base and a powder coat finish provides excellent rust protection. Lowest Prices for the best trailer hitch from Draw-Tite. Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" part number 75992 can be ordered online at etrailer.com or call 800-298-8924 for expert service.
  • All Info
  • Reviews (286)
  • Q & A (71)
  • Videos (9)
  • Photos
  • Why etrailer?

Draw-Tite Trailer Hitch - 75992

  • Draw-Tite
  • Class III
  • 2 Inch Hitch
  • 4000 lbs GTW
  • Concealed Cross Tube
  • 4000 lbs WD GTW
  • 400 lbs TW
  • 400 lbs WD TW
  • Custom Fit Hitch

Fully welded vehicle trailer hitch is strong and durable. Draw-Tite's Tested Tough guarantee ensures that this hitch exceeds industry standards. The combination of an e-coat base and a powder coat finish provides excellent rust protection.


Features:

  • Custom-fit trailer hitch lets you tow a trailer or carry a bike rack or cargo carrier with your vehicle
  • Computer-aided, fully welded steel construction ensures strength and durability
  • Tested Tough - safety and reliability criteria exceed industry standards
  • Easy, bolt-on installation - no welding required
    • Complete hardware kit and installation instructions included
  • Lifetime technical support from the experts at etrailer.com
  • Black powder coat finish covers e-coat base for superior rust protection
  • Sturdy, square-tube design
  • Ball mount, pin and clip sold separately


Specs:

  • Receiver opening: 2" x 2"
  • Rating: Class III
    • Maximum gross trailer weight: 4,000 lbs
      • Maximum GTW when used with weight distribution: 4,000 lbs
    • Maximum tongue weight: 400 lbs
      • Maximum TW when used with weight distribution: 400 lbs
  • Limited lifetime warranty


Draw-Tite Tested Tough

Draw-Tite Tested Tough

Draw-Tite's Tested Tough program provides testing standards far superior to those outlined by the Society of Automotive Engineers (SAE), the go-to source for engineering professionals.



Each Draw-Tite trailer hitch receiver undergoes extensive fatigue testing and static testing with the ball mount that is either supplied or recommended for use with that particular hitch, thus ensuring results that are applicable to real life use. Fatigue testing is also conducted on hitches rated for use with weight-distribution systems.


In addition, Draw-Tite performs static testing on a simulated automobile, as opposed to the rigid fixture used for SAE testing, resulting in a more true-to-life scenario.


etrailer.com Technical Support

At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.



75992 Draw-Tite Class 3 Trailer Hitch Receiver - Max-Frame

87682 Hidden Hitch Class 3 Trailer Hitch Receiver

Replaces 75709

Replaces 75526

Replaces 87433

Installation Details 75992 Installation instructions

This Product Fits The Following Vehicles



California residents: click here


Video of Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"

Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.




Video Transcript for Trailer Hitch Installation - 2013 Ford Edge - Draw-Tite

Today on our 2013 Ford Edge we're going to be installing and taking a look at the Draw-Tite Class III Trailer Hitch, part number 75992. This is what our hitch looks like fully installed. As you can see, everything's hidden except for the receiver tube and safety hooks. Now, this receiver has a 2 inch by 2 inch opening. As you can see, it has a nice round collar to give you that nice finished look. Now, this receiver's going to use a round style safety loop, and as you can see, there's still plenty of room even with an oversized hook.

It's going to use a standard 5/8 pin and clip. Now the smaller hole here is for a J pin stabilization device, which is great for any accessories that you might have that don't have their own anti-rattle. This receiver has a 400 pound tongue weight, and that's going to be the force pushing down, and it has a 4,000 pound trailer weight, which is the force it can pull. Now, when using a weight distribution system, the weight range don't change, but make sure you check with your vehicle's owner's manual that your vehicle can handle that. I'm going to give you a few measurements that will help you in deciding on accessories for your new hitch, such as a ball mount, bike rack, or cargo carrier. The center of the hitch pin hole to the outermost edge of the bumper is 5 1/2 inches.

Now, from the ground to the inside top edge of the receiver tube is 14 3/4 inches. Let me show you how to install it. To begin our installation we're going to need to lower our exhaust down, and we're going to have a hanger here, here, and one right behind the muffler. Now, I'm just securing a strap so that when the exhaust falls down it won't fall down all the way, just enough to support it. Now we're just going to take some spray lubricant and spray them down so it'll be a little bit easier to get them down. Next, we're going to be removing this screw right here that has this bracket.

Now, we're going to be using a 5 1/2 millimeter socket. We won't be reusing this, and we're just going to tuck this behind the bumper like that. Our next step is going to be modifying our heat shield. We're going to need to remove these two bolts that are on the outside frame rail. We're going to be using an 8 millimeter socket. Now, we won't be reinstalling these bolts.

We're going to need to cut a relief hole for this hole right here, so we can get access to it, as well as here. I'm going to go ahead and show you where I'm going to cut. As you can see, we have access to both the front and rear hole without our heat shield being in the way, and we're going to repeat the same process for the other side. We're going to take our fish wire and we're going to take the coiled end and insert it into the furthest forward hole until it pops out right behind the bumper fascia here. Now, it's kind of hard to see, but if you reach your hand up really close to where the exhaust cutout is, you can feel there's a spot in the frame that has a notch in it. That's where that fish wire is going to come out. This is where our fish wire came out. I do want to mention, when going in the back hole, the farthest point away, you want to be careful not to pull the wire all the way out. We're going to take our spacer block and we're going to put it on our wire. After that, we can take our carriage bolt and we're going to thread it onto the wire, just like that. Now we're going to take our block, and you're going to feel in that channel above the fascia here that there's a spot that has a wider opening and a thinner opening. We're going to push our block through there, making sure that we have enough room to get our bolt through. We push our bolt through, we can pull our fish wire down, and our bolt will come down right here. Now, we're going to repeat the same fish wire process with this hole right here. Now we're going to repeat the same process on the other side. With an extra set of hands we can set our hitch into place. Just going to want to put the pull wires into the appropriate holes. The heat shield is actually going to be sandwiched in between the hitch and the frame. Now, simply take the pull wire off and you're going to take the conical tooth washer, making sure that the teeth are facing towards the hitch and the nut, and we're going to loosely install it on our hitch. We can also install the rest of our hardware. With all our hardware installed we can go ahead and snug them down. We're going to be using a 3/4 inch socket. Next, using the hitch as a template, we're going to come to the rearward-most hole, and we're going to use a 1/2 inch drill bit just to mark the hole. Now we're going to come back with a pilot drill bit to make it a little bit easier. Now with the pilot hole drilled we can come back with the 1/2 inch drill bit and drill the rest of our hole. Now, you do want to drill with a 17/32 drill bit if you have it. If not, you can use a 1/2 inch and just wallow 00:06:35 it out a little bit so the bolt will fit. Now that we have our hole drilled we're going to repeat the same process on the other side. We're going to take our fish wire again and insert it into the rearward-most hole. Now, I've taken the fish wire and I've put a bend right about where it needs to come out. That way it'll direct it down. All right, with our fish wire out we're going to repeat the same process taking the block, feeding it onto the wire, and then taking our carriage bolt and threading it on. Now we can feed everything back into the channel and pull our pull wire through. Then we can pull our bolt through. Again, making sure the teeth on the conical washer are facing towards the hitch and install our nut and washer. We're going to repeat the same process with the other side. Now we can snug up our remaining hardware, again using a 3/4 inch socket. Now we're ready to torque down our bolts. Now, you're going to want to torque it down to the specified amount in your instructions. Now with all of our hardware torqued down we can put our exhaust back up. That'll finish up the look at the Draw-Tite Custom Fit Class III Trailer Hitch, part number 75992 on our 2013 Ford Edge.


Customer Reviews

Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" - 75992

Average Customer Rating:  4.8 out of 5 stars   (286 Customer Reviews)

Fully welded vehicle trailer hitch is strong and durable. Draw-Tite's Tested Tough guarantee ensures that this hitch exceeds industry standards. The combination of an e-coat base and a powder coat finish provides excellent rust protection.

- 75992
by:
2008 Ford Edge

Great product! Easy to install, and fit perfectly on my 2008 Ford Edge. The coiled wires to feed the bolts through the frame is a brilliant idea. Here's a tip: when you feed the bolt through the frame, leave the coiled wire attached because if you push the bolt back into the frame while raising the hitch and the coiled wire in not connected, you're in a world of hurt. Very impressed with this product and I have pulled several uHaul trailers with it already. 718591



- 75992
by:

quick ship, excellent product and video s! 705718



- 75992
by:
2011 Lincoln MKX

Great quality trailer hitch, very pleased. Slightly disappointed with having to store wiring harness for trailer inside vehicle 591538



- 75992
by:
2011 Lincoln MKX

I couldn't be happier with the price, service and quality of the trailer hitch I purchased through etrailer.com. The instructions were straight forward and the components went together without any issues. I had it installed at a local automotive shop and they were impressed. The product quality is very impressive for the price of the product. I would highly recommend this trailer hitch to anyone interested in a similar purchase. 565250



- 75992
by:
2010 Ford Edge

Great hitch! Ended up purchasing this for a 2010 Ford Edge Limited. Needed the hitch for hauling a rental trailer so that we could move a bunch of our stuff to our new home (about an 8 hour drive away). I came into the installation without ANY real automotive experience. With that in mind, the instructions and videos were absolutely phenomenal, and I honestly wouldn't have even attempted something this involved without feeling as confident as I did watching the videos. With that being said, if you're a complete novice like I am, plan on needing plenty of extra time for the installation. What I believe was listed as a 1 hour job (I can only assume this was for a mechanic, or someone with quite a bit of experience) took me 8-10 hours. The only difficulty I ran into was that 2 of the holes on the hitch didn't quite line up that well on the frame of my vehicle. I'm not sure if it was a defect in the hitch or my frame or what, but it was the only thing that wasn't ideal. We were, ultimately able to get it to work; it just caused some hiccups along the way. This is the only reason I couldn't give it a full 5 stars. As far as quality, though - I couldn't be happier. We made the trip with a full trailer behind us without any problems whatsoever. And the hitch that I wasn't ever planning on needing to use again, has been used numerous times since, now that people know we can pull a trailer. But I've never had to think twice about it. Great job etrailer.com! 656709


Comments
When a trailer hitch is constructed, the manufacturer uses softer steel in the side plates as opposed to the harder steel used in the crossbar and receiver tube. This allows the hitch the flexibility to move along with the vehicle to a certain degree. This flexibility can also allow the hitch to get slightly bent out of position during shipping and handling. The good news is that its very easy to fix this if you know a few tricks as shown in the linked article.
-- Mike L - 06/14/2019

56571

- 75992
by:

My 2007 is 5 years old and the rubber hangers for the exhaust were not as easy to remove as in the video. Getting the right angle and a short prybar was the answer, but it took nearly an hour to get the three hangers loose. A combination of heat and road dirt was essentially a weld that had to be broken loose. Other than that, the installation was as simple as the video made it look. the bolt to the fascia support is a 7/32 and that created a small search mission. Have it handy before starting. Such a simple step shouldn't cause a delay. The wires provided for the feed of the 4 main support bolts worked great. The spring steel is just what is needed and the bolts slipped through the gap and right into place. Amazing. When installed, the hitch is almost invisible--only the receiver can be seen. The wife is very pleased. Even factory hitches create more of a visual presence than this hitch and that is what she desired. Here are pics of the job... I'm very pleased with the outcome. 29258


Comments
You guys should be proud of your products, they are outstanding! And the instructions you provide even with video, make things so simple to install.Our first product from you was a hitch receiver system for our 2007 Edge. I wouldnt have tried to install it myself-or even purchase such an item-but your video made it look like I could do it....and I did! Yes, we still love your products and when we can, we buy Made in the USA!.
Gary F - 10/11/2017

29087

- 75992
by:
2013 Ford Edge

Very well-made solid product. Excellent shipping speed. I was able to complete the installation in just over an hour including dropping the exhaust, fishing wires through the frame and drilling holes for the front bolts. I'm not sure how the included instructions are but a quick watch of the online installation video the day before was all it took. I would absolutely recommend this. 676974



- 75992
by:
2013 Lincoln MKX

The etrailer install videos gave me the confidence to tackle this job. I used ramps to give me more room to work, and I actually enjoyed installing it. It took me an hour and a half. You will need an extra set of hands to get the receiver onto the frame, and be careful not to accidentally push the bolts back up into the frame while you're doing this. On this car, my dirt bike carrier sits nice and low, so loading and unloading is way more easy than if I use my truck. 474136



- 75992
by:
2011 Ford Escape

I purchased the hidden hitch (87433) and Curt T-Connector (C56160) for my 2010 Ford Edge limited. The products came packaged conveniently together and on time. The videos were invaluable to my successful installation of the components. Without them, I would have relied on trial and error to install the wiring harness. The video for the hitch was helpful, but installation can easily be completed using just the printed instructions that came with the hitch. I watched the video for the wiring harness, completed on a 2011 Ford Escape. There is another wiring harness (T-One) that etrailer provides a video for a 2010 edge that I used also. This was helpful in finding routing locations for wires. I deviated from the video in a few ways. First, I routed the 4-pole connector through a rubber grommet under the spare tire leading to the under-carriage. This places the connector directly between the dual exhaust, away from heat, and in close proximity to the hitch. Next, I routed the passenger side wiring harness through the rear body panel, under the lift gate threshold to the passenger side trim panel. The whole process took me about four hours. Most of the time was spent routing wires so they were out of sight. Side note: there are only four recommended lift points on a Ford Edge and they are pinch weld areas near the tires. I lifted the rear of the vehicle with a floor jack at the rear cross section of the sub frame. The front was less conspicuous, so I went with the pinch weld area near the front driver's side and used a jack stand as a safety measure. 191831



- 75992
by:
2014 Ford Edge

I purchased the Draw-Tite hitch for my 2014 Ford Edge SEL, don't plan to tow much but wanted the flexibility to use receiver hitch mounted accessories like bike racks and luggage storage. Choose the slightly more expensive Draw-Tite to avoid as much "modification" as necessary to my car. The instructions were good, needed to review the website pdf file once since they had just a little more detail than the paper copy provided with the hitch. The paper instructions made no mention of the need to drill the hole for the third hitch to frame bolt on each side (photos show hitch dry fit with undrilled hole location on each side). Install time was right on, took me just over an hour of work. Definitely easier to do this when the car is new and the exhaust rubber isolators are more flexible and the underside is clean. In addition to the small trimming of the heat shields as described by the instructions I had to make one small alteration to each heat shield to ensure the hitch to frame mounting bolts would clear the shields once installed. Routing the hitch to frame bolts and spacers through the frame with the supplied guide wires is more art than science and that is what took the majority of the install time. Completed all the work without lifting the vehicle (no rack or jack, photo shows exhaust supported with 2x4 blocks) and am very happy with the look and functionality. 183246



- 75992
by:
2010 Lincoln MKX

This is a pretty easy installation. The quality of the hitch, hardware, and instructions exceeded my expectations. I installed this by myself with only a floor jack and the recommended tools. It took about 3 hours from beginning to end. I would also add that eTrailer has videos on YouTube to help. Their customer service is excellent. I recommend both the company and the hitch! 573865



- 75992
by:
2009 Ford Edge

Fast shipping. The fit is perfect and it took me about an hour to install it. I am very pleased. 261825



- 75992
by:

Shipping was very fast for free option! Received in 2 days. All hardware was with the hitch. Instructions were decent. The instal video was great. My only complaint is your rear mufflers will rest against hitch. Overall great product, fast shipping, easy instal, and a clean finish. Happy customer. 770025



- 75992
by:

Ok so I got the hitch I ordered pulled the car In my garage put it up on my lift 65 minutes later I was done! This was everything Rebecca said PERFECT!!! Didn’t take pics while it was up but will send some 749771



- 75992
by:

Gave this hitch to my 17yo for his birthday. We installed on a Saturday. Took us about 2hours. The video install instructions were easy to follow and a great help. Overall, very satisfied. 745425



- 75992
by:

Well built hitch with good instructions, excellent fitment, timely delivery. 735881



- 75992
by:

This is a great choice for a 2013 era Ford Edge. I especially like that it is mostly hidden, except for the receiver tube. The first one that I ordered from Amazon was a bit beat up and not packaged well (one side was sticking out of the box) and the internal packing materials were just laying in the box. It looked like it may have been a returned item. Because of that experience, I decided to go with etrailer. That one was packaged properly and very clean. With an item like this it is inevitable have some small scratches. So the instructions say average installation time is 55 minutes, which is highly doubtful. Sure, there are a few people that may have acoomplished this, but not on average. I am a fairly skilled mechanic with lots of good tools (floor jacks, compressor, air and electric impacts and ratchets, etc.) and it took me quite a bit longer than 55 minutes. I will say that I don't have a full car lift, which would have helped some. I elected not to lower the exhaust which I think was a break-even in turns of time spent. With this approach, I used a rolling floor jack on each side of the hitch to raise the hitch into place and maneuver it over the exhaust. Also, the best way to drill through the frame for the two front bolts is to start with a smaller bit(s) and step up to the 17/32" (or 1/2" which works fine). All in all, I'm very happy with this hitch and etrailer. The reviews and videos were very helpful. 734418



- 75992
by:
2014 Ford Edge

I've ordered receivers for our company trucks and personal vehicles about twelve times and wiring harnesses about six times and trailer axles once from etrailer. All off the purchases have gone very well including shipping. I will continue to purchase from etrailer. 733362



- 75992
by:
2014 Lincoln MKX

Great product and a perfect fit. Just like factory just a whole lot cheaper. 732233



- 75992
by:

Works perfectly .watched u tube video instillation was straight forward and easy . Took about an hour . I was in no hurry 724739



- 75992
by:

Very knowledgable staff, great assistance, excellent product value, and fast delivery in a sturdy box. 717002



- 75992
by:

Adam was great! Fast, efficient and super friendly. Products arrived as described. Thank you Adam :-) 714676



- 75992
by:

Easy to install, didn't bother with the paper instructions. The videos are way better if you need clarification or help. My hitch came with one of the mount arms bent so I had to hammer it back into place. Could have been damaged in shipping. Other than that, seems like a good product for the price. Would have given 5 stars if it wasn't damaged. 704113



- 75992
by:

Hitch has performed as advertised and after salt and snow of the winter is still doing great. Wonderful product. 699399



- 75992
by:

Engineers designed the perfect hitch for my car. I love the low profile and the look. I will mainly be using it with a large utility trailer. Using a small vise grip pliers helped me hold the retrieving wire in place, while I attached the retaining plate and bolt. I needed a little help from customer service and they were great. The [online videos] helped with the installation. 698761


35
308
Show More Reviews

Ask the Experts about this Draw-Tite Trailer Hitch

  • Trailer Hitch and Wiring Harness for 2011 Ford Edge
    The Draw-Tite Trailer Hitch # 75992 is a great option for your 2011 Ford Edge though in terms of a wiring harness, there isn't a harness that is an external plug-in or that can be mounted externally unless you do your own modification and find a way to route the harness underneath your Edge. As you can see by the accompanying cut out of the reviews I added we did have one customer run the 4-way through the grommet on the left side of the spare tire in a '11 Edge. The most reliable wiring...
    view full answer...
  • Recommended Towing Hitch for 2010 Ford Edge SEL 2WD
    For your 2010 Ford Edge SEL 2WD I highly recommend the Draw-Tite Max-Frame Trailer Hitch Receiver # 75992 because of its hidden design. This particular Class III hitch, which is confirmed to fit your Edge SEL, features a drop-down 2" receiver that allows the crosstube to be completely hidden behind the bumper. This means only the receiver itself will be visible, which not only creates a sleek factory-like appearance but also helps provide better ground clearance for your ball mount and...
    view full answer...
  • Trailer Hitch and Wiring Recommendation for 2014 Ford Edge
    For your 2014 Ford Edge the hitch you would want for towing is the Draw Tite part # 75992 which is a confirmed fit and has plenty of towing capacity. It's a 2 inch hitch which is the most popular size for towing products so it's the best choice. I attached an install video for you to check out as well. It comes with all needed install hardware as well. If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a...
    view full answer...
  • What Is the Difference Between the Curt Hitch and the Draw-Tite Hitch on a 2010 Ford Edge
    Both the Curt Hitch # C13067 and the Draw-Tite Hitch # 75992 are custom fit hitches that are designed to be mounted on to your 2010 Ford Edge. Both hitches are Class III rated and have the 2 inch opening at the hitch. Both the Curt and Draw-Tite Hitches have a gross trailer weight rating of 4,000 lbs and a maximum tongue weight of 400 lbs. Both the Curt and Draw-Tite Hitch have limited life lifetime warranties. Of these two, I recommend the Draw-Tite hitch over the Curt for two reasons....
    view full answer...
  • Will the Ground Clearance of the Draw-Tite # 75992 on a 2011 Ford Edge be an Issue When Towing
    You should have no issues being able to tow a trailer behind your 2011 Ford Edge Limited after installing the Draw-Tite Max-Frame Trailer Hitch Receiver # 75992. You will simply need to find a ball mount that has the correct rise or drop to ensure that it is level. When we installed this trailer hitch on a similar 2011 Edge (see attached video) we found from the ground to the top of the inside of the hitch receiver was about 13-1/2 inches. You can use this measurement and the attached ball...
    view full answer...
  • Trailer Hitch Recommendation for a 2011 Ford Edge
    The Hidden Hitch part number 87604 that you referenced has been replaced by the Draw-Tite part # 75992 so that would be the hitch you would want. I attached an install video for you to check out as well. If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and...
    view full answer...
  • Trailer Hitch Recommendation On A 2011 Ford Edge SEL
    We have two Class III hitch receivers available for your 2011 Ford Edge SEL, Curt part # C13067 and Draw-Tite part # 75992. In order to tow a trailer with 2 jet skis, you will need the weight capacity a Class III hitch offers. I recommend the Draw-Tite Max-Frame Trailer Hitch Receiver as this hitch will not be as visible from above in comparison to the Curt Trailer Hitch Receiver. The Draw-Tite Class III hitch is rated for 4000 lbs. of gross trailer weight (GTW) and 400 lbs. of tongue...
    view full answer...
  • Trailer Wiring Harness Recommendation for a 2014 Ford Edge
    There are several trailer wiring harness options available for the 2014 Ford Edge. I recommend T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector Item # 118515 though because compared to the other options we hear about fewer problems with the Tekonsha brand. All of the harnesses install in the same way and provide the same functions but the Tekonsha harness is the best mix of quality and affordability for your Edge. I have linked a video showing an example installation...
    view full answer...
  • Which Trailer Hitch Will Fit a 2012 Ford Edge Sport
    I spoke with my contact at Draw-Tite and he said that the ground effects/rear fascia on a 2012 Ford Edge Sport prevent hitch # 75992 from fitting properly. I do have a trailer hitch that fits the sport model. It does require some trimming but not any extra trimming other than what is specified in the instructions. Take a look at the CURT Trailer Hitch # C13067. I confirmed with CURT that it will fit the 2012 sport model. I have included a link to the installation instructions for you...
    view full answer...
  • 2 inch Draw Tite Trailer Hitch Recommendation for 2014 Ford Edge
    For your 2014 Ford Edge we have two Draw Tite hitches that have a 2 inch opening like the part # 75992 that you referenced. The # 75992 is the correct hitch if your Edge is not a Sport model. If instead you do have a Sport model you'd want the # 75728. These are Class III hitches which have 2 inch openings which I believe is what you are looking for since this is the preferred size for most people. The heat shield will need to be trimmed to install this hitch. I attached a picture that...
    view full answer...
  • 2 inch Hitch Recommendation for 2007 Ford Edge with Factory Hitch
    I spoke with my contact at CURT and he stated that Trailer Hitch # C13067, will install on a 2007 Ford Edge with a factory 1-1/4 hitch. It will sit below the factory hitch. This hitch is a good choice for your 2007 Ford Edge, and will give you the 2 inch Class III hitch. Basically this will fit whether the hitch you have on your Edge is a factory one or an aftermarket one so it is a safe choice. I attached an install video for you to check out as well.
    view full answer...
  • Is the 17/32 Drill Bit Absolutely Necessary for Installation of Draw-Tite Hitch # 75992?
    The Draw-Tite Max-Frame Trailer Hitch Receiver # 75992 does state to use a 7/16 inch drill bit in the instructions. This is engineers helping with installation instructions for precision but you are correct most people will use a 1/2 inch bit or use a Dremel tool to slightly enlarge it. We reference this at the 5:35 mark of the attached video we used a 1/2 inch drill bit for installation.
    view full answer...
  • Hitch Recommendation for a 2014 Ford Edge LTD
    Both the Hidden Hitch part # 87682 (no longer available) and the Draw Tite Hitch part # 75992 will install in the same way. Both hitches are made by the same company and actually share the same installation instructions. No matter what hitch you install on your 2014 Ford Edge you will need to remove the support bracket. I can assure you that Draw Tite is very rigorous in how they test their hitch installs and if there was any risk that the fascia would get deformed they wouldn't advise...
    view full answer...
  • Will Only the Receiver be Showing on Draw-Tite Trailer Hitch for a 2013 Ford Edge
    Yes, only the receiver on Draw-Tite trailer hitch # 75992 will be visible after installation on your 2013 Ford Edge. Take a look at the picture I have included that shows the hitch installed. I have also linked the instructions for you. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch...
    view full answer...
  • Trailer Hitch Recommendation for 2012 Ford Limited with Higher Tongue Weight For Bike Rack
    For your 2012 Ford Edge Limited the trailer hitch we offer that has the highest tongue weight capacity and does not require a stabilizer strap when carrying a non-supported load is the Draw Tite part # 75992 which has a tongue weight range of 400 lbs which would be more than enough for a bike rack.
    view full answer...
  • Hitch Recommendation for a 2013 Ford Edge with Appearance Package
    The Draw Tite Hitch part # 75709 that you referenced is the exact same as the Hidden Hitch part # 87682 (which is no longer available). If you check the installation instructions for both that I attached you will see that they share the same instructions. Either hitch would work for your 2013 Ford Edge as long as you do not have the Sport model. Any 2 inch hitch ball mount should fit either hitch. For a ball mount, hitch ball, and pin and clip, I would recommend the etrailer Ball Mount...
    view full answer...
  • Trailer Hitch Recommendation for a 2013 Ford Edge Towing a Pop Up Camper
    If the dry tongue weight of your pop-up camper is 358 lbs then most likely it would be even higher when loaded and ready to tow. The best recommendation I can make would be for you to upgrade to a hitch with more tongue weight capacity like the Curt Hitch part # C13067 as it can handle up to 400 lbs of tongue weight. You will also need to check the towing capacity of your vehicle in the owners manual as well and be sure not to exceed the lower of the two figures. For trailer wiring...
    view full answer...
  • Is There Drilling Required to Install Trailer Hitch on 2011 Ford Edge
    Actually the hitch part number you mentioned of 87604 is no longer available but for a similar hitch made by the same company we have the Draw Tite # 75992 which would fit and work well. It does have drilling listed as a requirement as all of the current hitch fits for your 2011 Ford Edge require. I attached a picture that I took from the instructions that covers this step for you to check out as well as well as an install video.
    view full answer...
  • Necessary Modifications to Install Draw-Tite Class III Receiver on 2008 Ford Edge
    The Draw-Tite Class III Receiver you referenced, part # 75992 does not require any trimming or other modification of the bumper fascia. However, there are two heat shields that are attached to the frame members under the vehicle that will need a bit of trimming. If you look at figure # 2 on the install instructions that I have linked to, you will see a diagram showing the small portions that will need to be trimmed away. This hitch fits all Edge models except for the Sport model. To...
    view full answer...
  • Recommended Trailer Hitch for 2013 Ford Edge
    All of the available aftermarket trailer hitches for your 2013 Ford Edge do attach to the vehicle's frame to allow the receiver to sit just below the rear bumper, as you mentioned. The factory design does provide for a nice, clean look, but the aftermarket models do still feature a hidden design where only the receiver is visible from the rear. For your Ford Edge, I recommend the Draw-Tite Class III Max Frame Receiver Hitch # 75992. This Class III hitch is confirmed to fit your vehicle...
    view full answer...
  • Hitch Recommendation for a 2007 Ford Edge
    Yes, the Draw-Tite Hitch part # 75992 that you referenced has been confirmed to fit your 2007 Ford Edge so I would recommend it for you. I attached an install video that shows this hitch being installed on a 2008 Ford Edge for you to check out. For trailer wiring you would want the part # 118551. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch...
    view full answer...
  • Trailer Hitches Available for 2014 Ford Edge
    We do not have etrailer-affiliated locations in your area but each of the hitch manufacturers whose products we offer do maintain dealer-locator functions on their websites. I will send you links to those dealer locators in a separate email. Chances are our price for a hitch will be hard to beat, especially since we offer our Lowest Price Pledge policy which is detailed on the linked page. All hitches offered for the 2014 Ford Edge and the 2014 Ford Edge Sport are displayed on the other...
    view full answer...
  • Trailer Hitch Recommendation for a 2009 Ford Edge with All Wheel Drive
    The Draw-Tite trailer hitch, # 75992, fits all models of the 2009 Ford Edge except the Sport model so it will fit your AWD model provided it is not a Sport. If it is a Sport, you would use # 75686. In terms of what capacity you should use, you will need to consult the vehicle owners manual to determine what the towing capacity is of the vehicle as equipped and go by that. Even if a hitch is rated higher, you must go by the lowest rated component in the system. A qualified mechanic...
    view full answer...
  • Trailer Hitch Recommendation for 2014 Lincoln MKX for Bike Rack
    The hitch you mentioned has been discontinued so it's no longer available. The Draw Tite hitch part # 75992 is a confirmed fit for your 2014 Lincoln MKX though and would do a great job with a bike rack. You have to use all 6 bolts to install the hitch though. I really like the Saris Freedom Superclamp part # SA4025F. This is a lightweight platform rack (which is normally an unheard of combo). That means it'll be easy to install and remove from your vehicle since it's light, but also...
    view full answer...
  • Does Draw Tite Hitch 75992 Fit 2014 Ford Edge
    The Draw Tite hitch part # 75992 that you ordered is the correct hitch for your 2014 Ford Edge. I attached an install video below that shows this hitch installed on a 2014 Edge just like yours for you to check out too. Sometimes hitches can get slightly bent during shipping and this can be fixed by bending the hitch back into place as long as the hitch only has a slight bend to it. If yours isn't lining up I can almost guarantee that is what happened. Some people will use open steps...
    view full answer...
  • Replacing OEM Hitch Receiver on 2010 Ford Edge with Draw-Tite Max-Frame Hitch Receiver # 75992
    You will need to uninstall the factory 1-1/4 inch trailer hitch receiver from your 2010 Ford Edge. If it is a bolt-on installation then you will simply need to remove the bolts and take it off. If it has been welded on, you will need to hire a professional welder to cut the welds for you before installing the Draw-Tite Max-Frame Trailer Hitch Receiver # 75992. Once the OEM hitch receiver is out of the way you will be able to install the Draw-Tite hitch receiver. If you let me know...
    view full answer...
  • 2 inch Hitch Recommendation for a 2010 Ford Edge for Bike Rack
    For a 2 inch trailer hitch that would work great on your 2010 Ford Edge I would recommend the Draw Tite Hitch part # 75992. This hitch has plenty of tongue weight capacity for your bike rack and wouldn't require a stabilizer strap like the Curt does when used with bike racks. I attached an install video plus a video that shows a comparison of the hitches available for your vehicle. The Swagman XTC2, part # S64670 is one of the most popular racks because it's so easy to use, and because...
    view full answer...
  • Does Fascia Bracket of 2010 Ford Edge Get Reused After Hitch Install
    The fascia bracket of your 2010 Ford Edge will get bent back and not reused once you install the Hitch part # 75992 that you referenced. Check out the install video I attached for more info as well.
    view full answer...
  • Trailer Hitch And Wiring For 2007 Ford Edge
    The Draw-Tite trailer hitch we offer for your 2007 Edge is part # 75992. This is a Class lll hitch and it has a 2-inch receiver opening. I have attached a photo of the hitch installed on a Ford Edge. Although it is a different year vehicle the installation will look similar. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop....
    view full answer...

Do you have a question about this Trailer Hitch?




  • Why etrailer.com?

    At etrailer.com we guarantee:
  • Highest quality trailer hitch for the best price.

    Our Lowest Price Pledge ensures you will never overpay for the parts you need.
  • Real product know-how.

    We make sure that the products we sell are what we say they are, and that they work the way they are supposed to work. Get real advice from a real person who has the knowledge and expertise needed to solve your problem.
  • Most detailed, accurate trailer hitch information available.

    Because we take providing accurate product information seriously, we take our own detailed product photos, demo videos and installation videos, as well as verify measurements, instructions, and vehicle fit information.
  • Installations, made easy.

    We love helping people and have the most highly-trained customer service, hands-on experience, step by step videos and installation instructions.
  • Fast shipping.

    Your order is automatically routed to get out of our warehouse and to your door as quickly as possible. Receive free shipping on orders over $99.
  • Personalized service for life.

    We provide one-on-one, personalized service from the ordering process through the life of your product.
  • Trusted since 1946.

    We've been serving customers since our parts store first opened in 1946 and continue to be recognized by our customers, our vendors and third parties for exceptional service.
  • Returns Policy

    Need to return an item? No problem. Please read our Returns Policy for more information.

Info for this part was:

Test Fit:
Joe V
Test Fit:
Nicholas E
Test Fit:
Alan C
Test Fit:
Randy B
Test Fit:
Brent H
Test Fit:
Robert C
Test Fit:
Ryan G
Video by:
Andrew K
Video by:
Zach D
Written by:
Lindsey S
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Adam R
Expert Research:
Jeffrey L
Video Edited:
Joshua S
Video Edited:
Jacob T
Video Edited:
Andrew L
Video Edited:
Kathleen M
Video Edited:
Chris R
Updated by:
Laura H
Updated by:
Sarah W
Updated by:
Alexander C
Updated by:
Amanda M
Updated by:
Jenny M
Updated by:
Isabelle B

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.


Product Experts Available Now!
Call 800-298-8924