See what our Experts say about this CURT Trailer Hitch

• Does Gen-Y Anti-Rattle Clamp Work With 2 Inch Trailer Hitch on Ford F-150
  The Gen-Y Anti-Rattle Clamp for 2" Hitch Receivers # GY88XR is actually designed to fit over the shank of a ball mount or accessory that fits into a 2-inch trailer hitch like the Curt Trailer Hitch # C86HR that fits certain model year Ford F-150's and F-150 Raptors. So, the short answer is yes, the clamp will absolutely work with the hitch, but it does not go around the lip, it will actually go into the receiver and then you'll tighten it. If you take a look at the linked video review...
  view full answer...
• Is the Curt Trailer Hitch Receiver Part # C26HR Visible on a 2017 Ford F-150
  Yes, only the receiver tube opening of the Curt Trailer Hitch Receiver part # C26HR will be visible while installed on your 2017 Ford F-150. I have attached a photo of what the finished product will look like on a similar F-150 for you in addition to an install video. I also recommend using part # C22272 to protect the inside of the receiver tube from rusting while not in use.
  view full answer...
  
• How Does Brake Controller Install on 2019 Ford F-150 with Factory 4-Way
  To install a brake controller like the Hopkins Agility part # HM47295 in your 2019 Ford F-150 you'd actually just need the # 37185 which would plug into the 4-way you have at the rear of your truck and then you'd splice the blue wire of the adapter to the blue wire of the harness you can see in the attached picture. Instead of the Agility I would strongly recommend the iCommand part # TK63VR as it performs much better and is much more reliable as well. For a Class III hitch part # C86HR...
  view full answer...
  
• Wiring Harness For 2020 Ford F-150 Without Tow Package
  Where to start with your wiring harness depends on what available connectors you have under the bumper of your 2020 Ford F-150 and also what trailer connector you're looking to add on your truck. If your truck already has the square shaped connector, #C56110 will add a 4-way connector for your trailer. If you have a square shaped connector on your truck and want to add a 7-way connector for your trailer,the # ETBC7 is what you need. If you instead have a round shaped connector on your...
  view full answer...
  
• How To Prevent Rear End Sag on a 2018 Ford F-150 Raptor While Towing
  Yes, you can use a weight distribution system on your 2018 Ford F-150 Raptor. However, you will need to make sure the trailer hitch is rated for use with a weight distribution system. For one that is, I recommend the Curt Trailer Hitch Receiver part # C86HR which is a direct fit so no drilling is required and it will exceed the weight limitations of your vehicle. For a weight distribution system, there are few better than the Equal-i-zer Weight Distribution System part # EQ37061ET which...
  view full answer...
• Trailer Hitch Recommendation for 2019 Ford F-150 that Allows Full Size Spare
  Yes, the Curt hitch part # C86HR that you referenced does fit your 2019 Ford F-150 and will allow you to retain the spare you have stored underneath the vehicle. The spare does need to get lowered during the install process but it can easily be put back where it belongs after the install.
  view full answer...
  
• Trailer Hitch and Brake Controller Recommendation for 2016 Ford F-150 with 4-Way Trailer Connector
  For your 2016 Ford F-150 the Curt hitch part # C86HR is a confirmed fit and would work great. Then to convert the 4-way to a 7-way and install the brake controller would actually want the part # 37185 and the brake controller install harness part # 22292. Follow the 4-way trailer connector wires from the trailer connector to the front of the vehicle. These wires connect to a factory plug along the frame rail, usually on the driver's side, between the back tires and the rear bumper. The...
  view full answer...
  
• Is Curt Trailer Hitch Visible on a 2020 Ford F-150
  The Curt Trailer Hitch Receiver # C86HR has a hidden crosstube design which gives you a very clean look that is complimented by the matte black finish that matches black finish that you'll find on your 2020 Ford F-150. In all honesty, when looking for a low profile trailer hitch that looks like it's designed for the vehicle you can't go wrong with this trailer hitch. I am attaching an installation video, written instructions, and some photos so you can get an idea of how to install the...
  view full answer...
  
• Availability Of A Trailer Hitch For A 2024 Jeep Wrangler Willys Sport
  I do have hitches available for Jeep Wrangler, but we have not confirmed fitment for the 2024 models as of yet (July 2023). We hope to have fitment information within the coming months.
  view full answer...
• Is the Curt C86HR Hitch Hidden Behind the Bumper on a 2022 Ford F-150
  I have attached a picture of the Curt Hitch Receiver item # C86HR you referenced installed on a Ford F-150. As you can see it is mostly obscured by the bumper. The only part of the hitch that is visible is the 2" receiver portion. If you need a ball mount and ball I recommend the Curt Towing Starter Kit for 2" Hitches item # C45534. This towing kit will provide you with a 2" ball, a fixed ball mount with a 3/4" rise and 2" drop, and is rated for up to 7,500 lbs. It also includes a hitch...
  view full answer...
  
• Weight of Curt Trailer Hitch Receiver for 2019 Ford F-150
  The Curt Trailer Hitch Receiver # C86HR that fits your 2019 Ford F-150 weighs 39 lbs so it is very manageable for someone doing a self-install.
  view full answer...
• Wiring Harness For 2016 Ford F-150 Without Tow Package
  You are correct you will need a hitch as well as wiring harness and ball mount to tow your trailer. My hitch recommendation is the Curt Trailer Hitch Receiver # C86HR. It comes in a gloss black finish that not only resists corrosion but also is less susceptible to scratches. The Curt T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector # C56413 is a great choice connecting quickly and easily with no cutting or splicing of wires so you'll have the 7 way connector you need...
  view full answer...
• Recommended Trailer Hitch and Weight Distribution System for 2015 Ford F-150 with Travel Trailer
  If you have the Curt Trailer Hitch Receiver # C86HR, then I recommend upgrading your hitch to the Class IV # C26HR which is rated for up to 1,200 lbs when using weight distribution. The reason is because weight distribution is based on loaded trailer tongue weight as well as any cargo weight behind the rear axle of the truck. This can easily increase your loaded trailer tongue weight and put you beyond the max capacity of your hitch when using weight distribution. For your weight distribution...
  view full answer...
• Is Frame Mounted Hitch Solution Better than Bumper Hitch of 2016 Ford F-150
  If you are considering a frame mounted hitch over your bumper ball mount/hitch I would recommend you go ahead and go the frame hitch route. This will give you quite a bit more towing capacity and the ability to use a different rise/drop ball mount so that you can tow your trailer as level as possible. The Curt hitch part # C86HR would be a really great choice for this. It's mostly hidden too which gives it a less visible look. Check out the install video and picture I attached as well.
  view full answer...
  
• Options to Carry Bikes With 2016 Ford F-150
  We have a couple of solutions for you to carry bikes with your 2016 Ford F-150, though a tailgate pad isn't going to work for your 43 inch space because the narrowest pad is 53 inches wide, the Thule GateMate Pro Tailgate Pad # TH823PRO. The best option is a trailer hitch receiver and hitch-mounted bike rack. If you do not have a hitch on your 2016 Ford F-150 you can install the Curt Trailer Hitch Receiver # C86HR and add a 4-bike rack, with a great option being the Thule Hitching Post...
  view full answer...
• Wiring Harness and Ball Mount Recommendation for a 2018 Ford F-150
  The Curt Trailer Hitch # C86HR is an excellent choice for your 2018 Ford F-150. Then for wiring you can either install the Curt # C56110 if you have the rectangular OEM plug or the Curt # C55774 if you have the round OEM plug. Both of these options give you a 4-Way flat connector that will match up with your small utility trailer. Since pickups can be used for a variety of towing applications I highly recommend installing the B&W Tow & Stow 3-Ball Mount # BWTS10049B. This comes with the...
  view full answer...
• Will a Hitch Mounted Bike Rack On a 2018 Ford F-150 Raptor Trigger Blind Spot Sensors
  If you will be carrying bikes on the rear of a vehicle with blind spot sensors then you will want to turn these sensors off while you have the bikes attached as there is a possibility that the bikes or bike rack can interfere with them, same goes for the cross traffic sensors as well. The good new is that most vehicles allow you to easier turn these sensors off via the in dash settings. If you don't already have a hitch mounted bike rack, the Kuat Transfer V2 part # KU24FR is one of my...
  view full answer...
• Are There Extra Spacers in the Curt Trailer Hitch Kit # C86HR?
  The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # C86HR does not come with extra spacers. On each side of the hitch the rear most hole will use a square block spacer and a U- shaped spacer. The hole closest to the cab on each side will use a square block spacer on each side of the frame rail so one will be sandwiched between the hitch and the frame. I've attached a video that helps explain this to assist.
  view full answer...
• Replacement Square and U-Shaped Spacers for Curt 13118
  For the spacers for the Curt # C86HR you will need the # RHK. Enter the hitch number C86HR and then select Curt for the manufacturer. The Curt spacers are not available individually.
  view full answer...
• Bumper Clearance on Curt Trailer HItches for 2018 Ford F-150
  The Curt Class IV # C26HR, Class III # C86HR, and Class III # C13903 trailer hitches will all have almost identical bumper and ground clearance dimensions when they are mounted under your 2018 Ford F-150. There will be a distance of around 3-1/4 inches from the center of the hitch pin hole to the outermost edge of the rear bumper. What separates the models from each other are their Class ratings and their physical appearance when installed. Between the three options I recommend going...
  view full answer...
• Wiring for 2019 Range Rover HSE and Class III/IV Hitch for 2019 Ford F-150
  We don't have a hitch for the HSE Land Rover but we do have the 7-way trailer wiring kit # 118275. Then for a Class III hitch for your 2019 Ford F-150 we have the Class IV part # C86HR. The prices are available down below at the product links.
  view full answer...
• Trailer Hitch and Wiring Recommendation for 2017 Ford F-150
  For your 2017 Ford F-150 without a factory trailer hitch the most popular hitch option is the Curt hitch part # C86HR. We had the chance to install this hitch on a 2017 Ford F-150 (see attached install video link below), and found that it fit and worked really well. If you have the round 7-way trailer wiring connector already on your truck then all you need to use is the part # HM40975 to have trailer wiring. If you wanted to do some towing you might be interested in etrailer ball mount...
  view full answer...
• Will Spare Tire Fit After Installation of Curt Hitch C86HR
  Yes, your 2018 Ford F-150's spare tire will still store in the original location after installation of the Curt Class III hitch # C86HR. The photo I linked shows you the installed hitch's position and the ample room for the spare. Instructions and an install video are linked for reference.
  view full answer...
  
• Will Curt Trailer Hitch Fit Aftermarket Bumper on 2016 Ford F-150
  The Curt Trailer Hitch Receiver # C86HR that you referenced for your 2016 Ford F-150 has only been tested with the OEM bumper on a 2016 F-150 so I would not be able to tell you off-hand if it will work with the Trail FX Rld001ti rear bumper that you ordered. This is the same case with all of the trailer hitches on out site. Attached is a photo of the receiver with this trailer hitch installed on a 2017 F-150 (with an OEM bumper) as well as a diagram showing that from the closest mounting...
  view full answer...
  

Do you have a question about this Trailer Hitch?