Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Aluminum reversible ball mount easily slides into your hitch and can be used in either the drop or rise position. This ball mount measures 12" from the pin hole to the ball hole and can accommodate a hitch ball with a 1" diameter shank.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello neighbors, it's Brad here at etrailer. And today we're taking a look at the Brophy Aluminum Ball Mount and we do have those in a variety of drops. So we have a two inch, a four inch, six inch, and an eight inch, and that's going to meet your needs of the trailer and vehicle that you have. Having the ability to have an eight inch or a six inch strap on a vehicle with larger tires or is slightly lifted is great because not only can you still have your off-road clearance and look good lifted, you can still use this to pull your trailer and get the use out of your truck still. Our two and four inch drops are going to be great for your standard height vehicle on your truck or SUV that doesn't have a ton of ground clearance or isn't lifted. These are going to be a perfect height for you to attach to your trailer.
Not all trailers have the same height. So if you do tow a multitude of different height trailers, having the ability to put a rise just by flipping the mount itself is going to be a great option for you. Our two inch drop flipped around will actually give you a one inch rise. Our four inch drop flipped around will give you a three inch rise, our six inch drop flipped around is going to give you a four inch rise. And then finally, our eight inch drop is going to give you a seven inch rise.
Whichever size fits your vehicle well, it doesn't really matter when it comes to that weight capacity, they all share the same tongue weight of 800 pounds. And that's going to be the downward pressure on the inside of the receiver tube hitch. Now, as far as your towing capacity, which is the weight of your trailer, plus the accessories loaded, they can all hold up to 8,000 pounds. Those are some pretty impressive weight ratings. And that's going to allow you to tow anything from as small as a kayak trailer or a small utility trailer to something a little bit larger.
You can step up to bigger things to tow like a boat here or even a camper, so you're going to cover that whole range. Now, while these ball mounts are extremely strong, you also want to check to make sure that your vehicle and the hitch can actually handle the weight that you're towing. So it's important to check the specs on both the hitch and also your vehicle's owner's manual is going to tell you how much your vehicle can tow and take the lowest of those numbers just to make sure you're staying safe. Now, one of the best features that make these ball mounts really stand out from other ones are going to be the fact that they're made out of aluminum, which at first I worried about maybe how much it can handle, but seeing the weight ratings and comparing against a standard one here, which is relatively heavy, the aluminum really shines here as I can toss it around. It is lightweight and that's going to be nice for when you're not using it.
And you're storing it in your truck bed or behind a seat. It's a lot less weight flying around as you're making turns. Now all of these ball mounts are going to have a one inch opening for whatever ball you want to put in. Now they do not come with the ball themselves, but Brophy does offer quite a few options that will all fit this and they look great. While looking for a ball for your ball mount, you're also going to want to take a look at a hitch pin and clip, if you do not have one already. Now, this is obviously a necessary item to keep this in place. Now these are great. This is a standard five eighths, and it's going to hold it in place. But sometimes people see this nice aluminum here and want it for themselves. So it might benefit you to get a locking hitch pin and clip. And we have those here at etrailer. Some of our customers have said that this does fit relatively loose in the receiver opening, and I don't disagree with them, and that can make some rattle while driving around with your trailer hooked up, Brophy does offer a U-bolt style anti-rattle device. And that's going to cinch that up to your receiver tube opening and make it nice and secure and take away that rattle. Now, the only thing left to do is hook up to your trailer, cross up your safety chains here, plug in your wiring, and you can drop it in place and hit the road. And that was a look at the Brophy Aluminum Ball Mounts. Thanks for watching..
Average Customer Rating: 4.8 out of 5 stars (138 Customer Reviews)
Aluminum reversible ball mount easily slides into your hitch and can be used in either the drop or rise position. This ball mount measures 12" from the pin hole to the ball hole and can accommodate a hitch ball with a 1" diameter shank.Perfect for my Tahoe. I have a 2019 Tahoe LS 4x4 with the max tow package. The receiver is mounted higher than than on the truck it replaced. Six inches of drop appears to be just about right for my boat trailer.
I bought a new trailer that came with a tongue mounted jack stand. The problem was the hand crank was to close my truck and prevented me from lowering my tailgate while the trailer was connected, by about a 1/2 inch. I had a standard steel 6 inch drop Reece ball mount. This one has more weight capacity, but is half the weight of the older ball mount. It added just enough distance from the truck I can put the tailgate down!
I would not recommend this ball mount. It fits extremely loose in the receiver and rattles like crazy. I am concerned that the aluminum will wear away slowly and the rattling will increase over time.
Very strong sleek ball mount with great finish that I was unable to find in the Atlanta area. A dealer told me about etrailer.com. No seams or welds that might break over time. Using the ball mount with a 6000 # rated hitch ball to tow a 519Z Ranger bass boat behind an Escalade. Their customer service associate, Paula, was very helpful to locate the EA60 in their assortment.
Never thought I would call a trailer hitch beautiful. Well this one here is just that,,, beautiful!! The service with etrailer is exceptional, beyond my expectations. I will be back as needed and recommend to anyone needing trailer accessories
this online store. Side note, the very fast delivery is also over the top
Good looking drop hitch, chrome is not for everyone but this looks bada$$ on my wife's Range Rover Velar, using it to pull my Harley trailer. Beautiful!!
Beautiful Forged aluminum stinger hitch. Smooth edges won't catch on stuff and it will ride in the truck with less snagging on other items. Price was right too.
This is well built. As described/reasonably light.
Fast delivery as always and the product was spot on
Thanks etrailer.com
Still looks new and I pull a 16 foot trailer everyday for my business.
works as intended. I have two other aluminum mounts from other manufactures that fit more tight. Packing was poor and finish had scratches.
I required a 5" rise for a particular trailer, perfect fit
I really like this mount, as a matter of fact I own 3 different sizes of this mount. It's beautifully made, strong as an ox, no sharp edges or ugly bends. As mounts go this is a work of engineering art.
Has worked great with my new Escalade now my boat is at the proper height. plus it looks great with the bright finish... worth the money
Super strong, light, quiet and nice looking. Great product and performing perfectly.
Haven't used it yet,but it look to be of good quality and well made.
Nicely made with the right amount of rise my truck requires. Overall, excellent.
Great product and awesome customer service experience. With fast shipping!!!!
Easy website to navigate. Great and on time delivery. Exceptional customer service.
Great product much lighter than what I was using, and very pleased with it's finish.
Sturdy, shinny...a must have. The coustomer service was excellent!
Nice product. Have not used it yet.
Looks
It looks like it will be durable quality product.
Looks good, appears well made. Works just like a solid bar of metal ought to.
High Quality & Looks great
Do you have a question about this Trailer Hitch Ball Mount?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Mike L.
8/9/2018
As with any manufactured product, the outside dimension of the ballmounts shank will have an acceptable tolerance. The same goes for the inside dimension of the hitch receiver tube. Occasionally, there will be an accessory thats on the small side of tolerance used in a receiver thats on the large side of tolerance. In that case, there will be some movement of the ballmount in the receiver. According to CR Brophy, the manufacturer, this is perfectly normal and wont cause any problem. If the movement is concerning to you, there are anti-rattle devices available such as RM-061 that will force the shank of the hitch accessory up against the side of the receiver tube so it wont move around.
Helpful Links
Hitch-Anti~Rattle/Roadmaster/RM-061.html