See what our Experts say about this Redline Trailer Bearings Races Seals Caps

• How to Measure to Determine the Correct Grease Seal for a Trailer Spindle
  The # 168233 Double Lip Grease Seal has an outside diameter of 2.332 inches and an inside diameter of 1.688 inches. This seal is not compatible with a AF2527E seal with a O.D 2.312, because, even though the O.D. id very close, the inner diameter of the is seal is 1.750 inches and would not be the correct fit for the spindle diameter. You will need to take an accurate measurement of the outside diameter of your existing seal, or the inside diameter of the mounting surface for the seal in...
  view full answer...
  
• 2004 Trail-Lite 8304-S Lift Kit Availability
  Since we know your 2003 Trail-Lite has a Dexter torsion axle with a 2,800 lb capacity the correct lift kit is the part # K71-707-02. This will give you a lift of 2-5/8 inches.
  view full answer...
• Replacement for Grease Seal With 2.332" OD and 1.75" ID
  Hi Walter; there is a little bit of room for grease seals to flex but that only works when it is a really small difference. The 1.50" ID of the # TMK89ZR is going to be too small for your spindle. What you can use instead is the # 10-42 which has a 1.75" ID and 2.33" OD. The 0.002" difference in the OD won't be an issue.
  view full answer...
  
• Replacement Bearings, Races and Grease Seal For a UFP HD-1377-10 Trailer Hub
  Based on previous information we have for your UFP HD-1377-10 hub it uses the following components. I do recommend pulling one of your hubs to verify that the replacements listed below match your current parts. Inner Bearing # L68149 (Inner diameter 1.378") Inner Race # L68111 (Outer diameter 2.361") Outer Bearing # L44649 (Inner diameter 1.063") Outer Race # L44610 (Outer diameter 1.980") Grease Seal # 10-42 (Inner diameter 1.75", Outer diameter 2.33") If the numbers or dimensions do...
  view full answer...
  
• Replacement Grease Seal for Hadco LA370R 6 On 5-1/2 Hub
  We don't offer a grease seal that would have the proper outer diameter to work with your Hadco Hubs, but we might have a solution that would allow you to upgrade your existing hub/drums so they're compatible with easily obtainable grease seals. If your Airsteam uses a standard 12 inch brake assembly like # 23-106, you can replace your hubs using # 8-201-5UC3-EZ which uses the readily available 10-10 grease seal. The hub/drum is compatible with the 25580 inner and LM67048 outer bearing...
  view full answer...
• Replacement Bearings for a HADCO LA370R Idler Hub w/ 25577 and LM67048 Bearings
  Hey Andy thanks for the pictures and the information! I am sorry but we do not have an old Hadco catalog lying around. We do not carry the 25577 bearing but it does have the same inner diameter of the 25580 bearing item # TMK44FR and the outer diameter is within .001" so it should work as a replacement. To replace your LM67048 bearing you'll want the Timken Replacement Trailer Wheel Bearing item # TMK56FR.
  view full answer...
• Replacement Bearings, Races, Grease Seal and Tools Needed For Dexter 8-283 Brake Drum/Hubs
  Your Dexter 8-283 brake drum will use a # 10-42 grease seal. If you are looking to replace all the races, bearings and seals you will want the following components per hub. Inner Bearing # LM67048 Inner Race # LM67010 Outer Bearing # L44649 Outer Race # L44610 Grease Seal # 10-42 We do have the following tools to make the replacement easier. Seal Puller # PTW1219 Install Kit # PTW83020 Bearing Packer # PTW1218 Grease # L11390 Grease Gun # L30416
  view full answer...
  
• Which Bearings, Races, and Seal Fit Dexter Hubs 8-283
  For the inner bearing you need # LM67048 and race # LM67010. The outer bearing is # L44649 and race # L44610. The seal is # 10-42.
  view full answer...
• Bearing Kit Recommendation for a Dexter 2800 lb Axle
  The bearings you would need are inner bearing # LM67048, outer bearing # L44649 with a # 10-42 seal. We don't have this as a kit but you can order each individually. We contacted Dexter and they informed us that you axle was made specifically for Fleetwood in Canada and they don't use the standard 3.5k bearing setup.
  view full answer...
• Replacement Bearings for Dexter 2,800 lb Axle
  The bearings you would need are inner bearing # LM67048, outer bearing # L44649 with a # 10-42 seal. We don't have this as a kit but you can order each individually.
  view full answer...
• Bearing Kit with LM67048 and L44649 Bearings
  I do have all of the parts you need but we do not offer an all inclusive bearing kit with them. Instead, you will need to purchase each separately using the list I have attached for you below. Inner Bearing - part # LM67048 Inner Race - part # LM67010 Outer Bearing - part # L44649 Outer Race - part # L44610 Grease Seal - part # 10-42 Tang Washer - part # 5-101
  view full answer...
• Is there a Bearing Kit for L44643 Bearings that Includes Races, Pin, Dust Cap, and Seal 203025
  The bearings we have, # L44643, and the associated race is # L44610. The cotter pin is # 165649. The dust cap associated with hubs that take these bearings is # RG04-020 for a pair. The seal on the other hand is an odd size. There isn't a bearing kit that has the seal that you need and it is an odd size that we do not carry. But it is readily available at auto parts stores. I know that a kit would make things a lot easier but in this situation there isn't a kit that has the seal and dust...
  view full answer...
• Correct Bearing Seal For a Dexter 2,800 Pound Axle
  I have confirmed with my contacts at Dexter, and the Electric Brake Shoe part # bp04-065 that you referenced was used on a very specific Dexter 2,800 pound axle. The correct seal for this axle is the # 10-42. This seal has an inner diameter of 1.75 and an outer diameter of 2.33 inches. This axle was manufactured by Dexter and had a manufacturer part number 010-042-00. This axle was primarily used in the lightweight travel trailer industry.
  view full answer...
• How to Determine Which Grease Seal is Needed for Trailer Hub
  Grease seals are very specific which means you will need some very specific information in order to get the one that fits. The ID tag info you gave is the axle capacity and tire size, but I can help you figure out just how to determine the correct grease seal, as well as bearings if you are looking for replacements for your hub. Doing this does require you to take apart your current hub assembly and look at the bearings and seal; wipe away the grease and you should be able to see the part...
  view full answer...
  
• Measurements and Compatibility of the Redline 10-42 Grease Seal
  The Redline Grease Seal item # 10-42 is going to be the closest seal we have to your measurements of 2.335 OD and 1.789 ID. The .03 difference could be caused by a measuring issue like your caliper being off by a small amount. If not the seal has some play in it and should work on your spindle.
  view full answer...
• Bearing Kit for Older Trailer Hub with LM67048 Inner and LM11949 Outer Bearing
  We don't offer a kit for that hub, but we definitely have the bearings and races and possibly the seal which can be purchased individually. You'll need the # LM67048 bearing, its # LM67010 race and the # LM11949 bearing and its # LM11910 race. I don't have enough information to determine the grease seal you'll need, but it'll have an outer diameter of 2.328 inches. We offer two seals with this OD. You can determine if one of them will work for you by using a digital caliper like # PTW80157...
  view full answer...
• Bearings For 1-1/16" & 1-3/8" Inner Diameter & Seal With 1-3/4" Inner Diameter
  Hi Joel; we have bearings and a seal with those measurements. For a bearing with a 1-1/16" (1.063") inner diameter what you need is Bearing # L44649. Then for a bearing with a 1-3/8" (1.375") inner diameter the correct part is Bearing # LM48548. There are a number of grease seals with a 1-3/4" (1.75") inner diameter though, and they all have different outer diameters so you are going to have to know what that is to get the right one. There isn't a hub we have or that I'm aware of which...
  view full answer...
• Replacement Grease Seal for Dexter 8-133 Trailer Hub
  Based on your dimensions you need seal # GS-2125DL. This seal has an outer diameter of 3.376 inches and an inner diameter of 2.125 inches. Seal, bearing, and race measurements need to be as accurate as possible which is why they are measured to the thousandth of an inch. I recommend measuring the diameter of the spindle where the seal rides as well as the hub opening where the seal fits using a caliper to ensure this seal will fit.
  view full answer...
• Correct Grease Seal for Dexter 2,800 Lb Axle
  The correct grease seal for a Dexter 2,800 Lb Axle is the Grease Seal part # 10-42 which has an inner diameter of 1.75" and and outer diameter of 2.33". In order to repack the bearings, I recommend using the LubriMatic Prime Guard High Temperature Wheel Bearing Grease part # L11380. If you want, you can use the Powerbuilt Deluxe Bearing Packer part # ALL647646 to make this job very easy.
  view full answer...
• How to Install New Grease Seal on Trailer Hub
  Based on the information you provided, the # 10-42 grease seal is the correct one for your application on the now obsolete Dexter 8-283 hub for 2,800 lb axles. To install it, with the inner bearing in place, set the grease seal over the top and press it in all the way, until it's flush with the rear of the hub bore. You can use a block of wood and a hammer or rubber mallet to apply even pressure around the seal, to push it back into the hub. And yes, you want the grease seal to be butted...
  view full answer...
  
• Grease Seals with Inner Diameter of 1.750-Inches
  We offer three grease seals that have a 1.750-inch inner diameter. You can see these by clicking on the link provided. The three seals have outer diameters of 2.312, 2.356 and 2.722-inches. You can use a digital caliper like # PTW80157 to measure your hub's bore to find out which seal is the proper fit. For example, part # 10-42 is a single-lip seal with an outer diameter of 2.33-inches meant for Dexter 2800-lb axles.
  view full answer...
• Replacement Hub/Drum and Brakes For a UFP 10" Hub/Drum Stamped HD 1377 On EZ Loader Boat Trailer
  Based on previous information we have for your 10" UFP HD 1377 hub it uses the following components. I do recommend pulling one of your hubs to verify that the replacements listed below match your current parts. Inner Bearing # L68149 (Inner diameter 1.378") Inner Race # L68111 (Outer diameter 2.361") Outer Bearing # L44649 (Inner diameter 1.063") Outer Race # L44610 (Outer diameter 1.980") Grease Seal # 10-42 (Inner diameter 1.75", Outer diameter 2.33") If the inner diameters match you...
  view full answer...
• Grease Seal to Replace National # 470316 for 2005 Rockwood Travel Trailer
  I was unable to locate any cross-reference information for the National 470316 grease seal you mentioned. I spoke with my contact at Redneck Trailer Supply, where we get most of our bearings and seals from, and he came up empty handed, as well. This is not to say that I cannot find a replacement for you, though. Take some good, accurate measurements of the outside diameter of your existing seal, and the diameter of the surface of the spindle where the seal would ride, which is dimension...
  view full answer...
  
• Replacement Bearings and Seals for Agricultural Hub
  Unfortunately we don't have a hub replacement available as you have an odd sized Agricultural Hub. However, I believe I can help you with bearing replacements. You will want # 14125A and # LM11949 for your bearings. The for your seal, you will need to determine fit based on the outer diameter of your hubs. We have the # 10-42 which has an outer diameter or 2.33 inches, # SL175 with 2.722 inches, or # 1105-100-031 with 2.356 inches.
  view full answer...

Do you have a question about this Trailer Bearings Races Seals Cap?