Correct Grease Seal for Dexter 2,800 Lb Axle

Question

Question:

What grease seal is used on a 2800 lb Dexter axle? The RV is a 2021 Coachmen Freedom Express 192RBS. This is a tandom axle RV. Thank you....

asked by: Brent

0

Expert Reply:

The correct grease seal for a Dexter 2,800 Lb Axle is the Grease Seal part # 10-42 which has an inner diameter of 1.75" and and outer diameter of 2.33". In order to repack the bearings, I recommend using the LubriMatic Prime Guard High Temperature Wheel Bearing Grease part # L11380. If you want, you can use the Powerbuilt Deluxe Bearing Packer part # ALL647646 to make this job very easy.

expert reply by: Conner L

0

Answer 1

The bearings you would need are inner bearing #LM67048, outer bearing #L44649 with a #10-42 seal. We don't have this as a kit but you can order each individually. We contacted Dexter and they informed us that you axle was made specifically for…

view full answer...

Answer 2

Hey Jason, yeah that's a Dexter 2,800 lb capacity axle that there are current replacement parts for. The bearings you would need are inner bearing #LM67048, outer bearing #L44649

view full answer...

Answer 3

For the inner bearing you need #LM67048 and race #LM67010. The outer bearing is #L44649 and race #L44610. The seal is #10-42.

view full answer...

Answer 4

Hey Kaleb, it's great to hear from you again! The Grease Seal #GS-2250DL is the best replacement for your Peer POS2253337TBN. I wasn't able to find a cross-reference chart, but I was able to find a document on the Peer website that explained…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Correct Grease Seal for Dexter 2,800 Lb Axle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching