To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Low-profile, aerodynamic crossbars create an aftermarket roof rack for your vehicle. Aluminum bars have T-slots that let you mount channel-mounted carriers and accessories. Flexible rubber strips in T-slots keep out dirt and won't need trimming.
Features:
Specs:
These low-profile Inno Aero crossbars let you build a stylish, aerodynamic roof rack for your vehicle. The crossbars require 4 Inno Flush or Through feet to mount the rack to your roof. You may also need a custom fit kit to mount the crossbars. Built-in T-slots in the tops of the bars let you easily mount carriers and accessories on the rack. Flexible rubber strips in the channels keep out dirt and require no trimming or adjustment. The crossbars are also constructed of strong yet lightweight aluminum so they won't rust.
These lightweight bars have an elliptical shape. This aerodynamic, low-profile design helps to reduce wind noise and drag when you drive. This means you won't need to add a fairing.
Inno Aero crossbars are constructed of sturdy, lightweight aluminum. Internal extrusions add strength and structural rigidity without adding a significant amount of weight. The bars are rustproof so you can leave them on your roof all year long, wherever you go. The sand-blasted powder coat finish resists corrosion, scuffs, and scratches. And the matte black color will look good on any vehicle.
Each crossbar has a channel in the bottom that lets you install Inno feet (sold separately). Slide the channel cover over to reveal a mounting hole for the foot. Clip the foot into the crossbar and then slide it into place along the channel. Built-in bar end stops in the channels will keep the feet from sliding off the edge of the bars.
To complete installation, mount the feet to your roof. You may also need a custom fit kit. Attach the locking covers (included with the feet) to secure the roof rack to your vehicle. Locking the covers also secures T-slot-mounted accessories to your crossbars.
Each bar has a built-in T-slot that allows you to mount bike racks, watersport carriers, ski racks, and more. The EZ-Slide rubber strip in each bar lets you mount accessories without the need to remove or trim the strip. Just press down on the ends of the flexible strips and slide your accessory's mounting hardware into the T-slots. These strips have a plastic coating so it's easy to slide T-bolts along the channels. Each strip runs the full length of the bar, so it helps keep dirt out of the channel when you're not carrying accessories.
You can also attach most clamp-on accessories to the bars, and the rubber strips provide a no-slip cushion for any accessories that rest on them.
Average Customer Rating: 4.8 out of 5 stars (252 Customer Reviews)
Low-profile, aerodynamic crossbars create an aftermarket roof rack for your vehicle. Aluminum bars have T-slots that let you mount channel-mounted carriers and accessories. Flexible rubber strips in T-slots keep out dirt and won't need trimming.Perfect fit on our vehicle and they feel strong and sturdy. Install wasn’t bad either. Very happy with the kit at this point and will test them out this weekend.
Shipping and packaging was very good and delivered on time!
Glad I went with the Aero cross bars for the less wind noise!
This inno rack fits well with my car. I installed a cargo box with it. The roof rack is well built and sturdy.
I like that the bars don't extend too much beyond the width of the vehicle (2012 Toyota Prius V). No noticeable wind noise or fuel economy change. They held two bikes just fine.
Good racks, one year of frequent use and no problems. The instructions could have been clearer, but once I figured it out it was easy to install.
Nice aerodynamic bars.
Fit well and easy to install. Excited to hall the bike around once the weather warms up.
..GREAT SERVICE ..thankU...
Product still looks great
..GREAT SERVICE ..thankU
Review from a similar Elliptical Roof Bars in Roof Rack
Got these with the custom fit kit (INK860) and the through feet/stays (INXS250) for my 2014 Ford Fusion Hybrid. Assembly's not difficult, though you do have to work with three different instructions: 1 for the stays/feet (the main install instructions), one for the Crossbars (minimal to do there), and one for the custom fit kit (again, minimal, though this one is crucial as it contains the measurements for the setup).
Things went pretty smoothly. However, when I put it on my roof at the measured distances from the center line, the feet didn't both occupy the rain gutter as they are supposed to. I checked the measurements, and both the front stays were at 21.5" and both back stays were at 21 3/8 " . Since those were the called for measurements, I'm not sure why I didn't fit perfectly. However, they're great and I can't wait to put them to use with my kayak and snowboard and bike. Thanks E-Trailer.
Photos show how great the system looks as well as some of the gaps at the rain gutters. I don't think it's crucial to readjust those. I did try several times but couldn't seem to get them just right.
Review from a similar Elliptical Roof Bars in Roof Rack
I have a 2022 Lexus GX460 Premium. Fairly simple installation and a almost seem less transition from the fit kit to the cross bar system. Can be done by one person, but I would suggest a two-person system to expedite the process
Review from a similar Elliptical Roof Bars in Roof Rack
Once again etrailer.com delivers. Finding a crossbar solution for my 2021 Lexus GX 460 was far more challenging than expected until I visited the site and found exactly what I needed. The fit kit worked great and the quality of the feet and crossbars on par or better than other brands (who dropped the ball on having a product available for this vehicle). The rack is on, secure and now carrying my Thule cargo box. Very happy.
Review from a similar Elliptical Roof Bars in Roof Rack
Originally, I was waiting for the Yakima crossbars to be restocked for my GX460 but decided I couldn’t wait it out any longer and went with the Inno’s aero set. Overall, they look great, fit great and seem to be very good quality. I was able to assemble the rack myself, it took me about an hour and half, I wish the installation was a bit easier but after watching the video from etrailer it all came together perfectly !
Do you have a question about this Roof Rack?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.