Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This actuator comes unassembled and unprimed, which makes it ideal for welding directly to your trailer tongue. Since the internal parts aren’t installed yet, you don’t have to worry about heat damage during the weld. Once it’s mounted, you can prime and paint it to match your setup. There’s no disassembly or extra prep work—just a clean, straightforward install that’s ready to go.
The built-in 8" adjustable channel gives you plenty of flexibility when setting up your coupler. You can mount different attachments—like a ball coupler, lunette ring, or clevis (each sold separately)—in one of three positions to get the height just right. It’s a simple way to make sure your trailer sits level and to fine-tune things for your specific towing setup.
The composite master cylinder is made from glass-reinforced nylon that stands up to rust and corrosion. Its large reservoir increases brake fluid capacity, helping prevent the system from running low on long hauls. The automotive-style diaphragm cap keeps the fluid sealed off from dirt and moisture, which helps maintain consistent braking performance over time.
The included breakaway feature adds peace of mind whenever you’re towing. If your trailer ever separates, the breakaway lever automatically activates the brakes to bring it to a stop. A safety cable with a snap hook connects securely to your hitch, so the system is always ready when you need it most.
With heavy-duty steel construction and weld-on installation, this actuator is built for serious use. It supports up to 12,500 lbs gross towing weight and 1,250 lbs maximum tongue weight on trailers with hydraulic drum brakes. The smooth acetal copolymer lining keeps the actuator telescoping easily in and out for dependable braking every time you slow down or stop.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're going to take a look at the Demco unassembled hydraulic brake actuator for drum brakes. This is in a raw finish. This one has a 12500 pound weight capacity. This surge type actuator comes unassembled, unprimed, ready for welding. As you can see, everything on the table here is included, so it comes with all the parts that are needed to assemble the brake actuator. This hydraulic brake actuator will activate your trailer brakes when your tow vehicle slows or stops. Right now it's unassembled, unprimed, makes for quick and easy welding.
You do want to make sure, though, that when you do weld this, you want it do it while it's unassembled so you prevent damage to any of the internal components. Right up front here, you can see it has a nice adjustable channel, with three different mounting positions for your coupler. This is a channel center design. The master cylinder right here is a composite master cylinder. It's very durable an efficient. It's made of a glass reinforced nylon construction, resists rust and corrosion.
If I take the lid off, you can see on the inside, has a nice large reservoir to provide increased capacity for brake fluid, and on the cap, on the top, there's the automotive style diaphragm cap which will create a nice completely enclosed system, to help prevent contamination of the fluid. The breakaway set right here, the breakaway lever, which activates your trailer brakes if your trailer disconnects from the tow vehicle. You can see on the cable here, on one end, they have a very large heavy duty snap hook that you snap on to it. This will ensure that you get a secure connection to your breakaway lever. These two pieces here, what will go on the inside, and this is what This is an Acetal copolymer lining. It provides a nice smooth operation as this actuator will telescope in and out of your base right here. This is made of a heavy duty steel construction.
Again, it is a weld-on installation. This part is made in the USA. A few specs on this again, the application's for trailers with hydraulic drum brakes. Gross towing weight capacity is 12500 pounds. Maximum tongue weight is 1250. Now, the width on the channel right here that you mount your coupler to.
I'm going to write it, internal dimension is 3". The heighth, which is from the bottom to the very top, is right at 8". This is designed to mount on a straight, 3" wide trailer tongue, and this also goes by the model number of DA10. One last note I do want to mention on this, is because this actuator does not include a reverse lockout, it is recommended that you equip your trailer with free backing brakes so that you can drive in reverse without the actuator triggering your trailer brakes. That should do it for the review on the Demco unassembled hydraulic brake actuator for drum brakes, in a raw finish, with a 12500 pound weight capacity.
Ratings & Reviews
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.





Brent
6/8/2025
Perfect