Best 2009 Toyota Highlander Trailer Lights

I've had my 5' x 10' tilt bed trailer for almost eleven years ago. I mainly use it to haul riding mowers, and going to the dump. Replaced the lights about five years ago with a cheapo set of lights. They never were very bright, and only worked sporadically. These are a quality upgrade that should last a long time. Installation was straight forward and painless. And they're MUCH brighter than either of the previous incandescent sets.

Item arrived in very secured packing, shipping was fast, the quality is very good, I will buy again from you, Thank You.

Really cheap. These lights are marketed as submersible, but based on what's in the package I'm really dubious. The lens bodies are not sealed. As you can see My photo, each lens body has a clearance hole for the wire - No gasket, and plenty of room around the wire, So water will definitely flood in and submerge the contacts and bulb/socket If you put these on a boat trailer. Additionally, to Make the wire connections. They give you wire nuts. For submersible wire connections, at the very least, you should use crimp butts wrapped in tape - or better yet a heat shrink crimp butt. But they give you wire nuts, which aren't even really stable against vibration, let alone moisture. It does say 3-year warranty on the package, however, so I guess I'll be testing that out.

Product was exactly as represented. Ordering was easy and I was notified of status of my order. Would recommend to my friends. Charles

LIGHT WAS EXACTLY WHAT I WANTED...WORKS GREAT!

LIGHT WAS EXACTLY WHAT I WANTED...WORKS GREAT!

Installed the new lights today. Easy peasy. I grew up on a farm, in the country, and have been fixin' and futchin' with trailer lights since I was 6, it seems (I'm 74 now). Hopefully this is the last time I'll need to fix the lights on this particular trailer.

Just like every other order from e trailer was

They look great installed. Only recommendation I can make is to include crimp connectors at least for the side marker lights and perhaps a small length of protective wire wrap. All in all I’m very pleased.

Very bright light, same connectors as my 2001 Shoreland'r boat trailer, just had to plug them in. Cannot say enough about the staff at etrailer, very helpful.

SPLENDID! Popped the old incandescent Side Marker Lights out on my 2008 Triton 21X2 trailer and installed these Thinline LED Clearance and Side Marker Lights (both the AMBER and RED ones). Just Plug-N-Play and my boat trailer looks AWESOME! Shipping was a snap!

I am very pleased with these lights. The lights on my trailer prior to this were dull and hard to see but these lights are bright and easily seen by cars behind me even during the day. Highly recommend.

As usual from etrailer, the product is as designed and works as it should. Shipping is slower than amzn and wmrt, but the tech support makes it worth waiting.

I purchased two of these LED Utility Light Bars and installed under the bed rail in my pickup bed in order to light up the bed area at night. The lights were easy to install along with the chrome base mounting bracket. Looks great and supplies ample lighting in the bed area. I liked the overall length which spread the light over a large area.

I installed a pair of these lights on underside of the overhang on my 5th wheel camper. They make hooking up easier as well as provide a lot of light for parking bicycles or motorcycles under the camper. Easy electrical hook up. I applied a bead of silicone RTV around the lights to prevent rain or wash water from getting inside the camper skin.

Bright, modern look, bright, well made. Standard plug made everything easy peasy.

The size was right, and the brightness of the LED light, let's people know there is a trailer in front of them, especially when braking, or making a turn

I had to replace one burned tail light on my 2005 cargo trailer. I bought two and replace the other one as well. They work perfectly. The size and the 3 pins connction are the same as the original. A little downside is regarding the packaging. I would expect each light wrapped individualy to avoid the rattling in the box. See pics.

Good replacement for the older versions

Did have a problem with shipping never trust our us mail etrailer made good then some, will continue to do bussiness with them they have the same idea as my business every customer is important no matter what the $ is top notch company in my opinion! ! Will post pics of lights once my customer picks up trailer thanks again etrailer /mark . Ur company made a good choice in u

Inexpensive and easy to install. Mounted on a rough riding horse trailer and over thousands of harsh terrain, the lights work flawlessly.

POS used by Thor to make you purchase a $[XX] plus hunk of plastic to replace a fifty cent light bulb! What [bull]. Warren Buffet screwing the little guy.

Product worked perfectly for what we were using it for. I purchased a motorcycle and needed to move the license plate bracket to be able to add bags. I found your bracket online, knowing we were going to have to jerry rig it to where we wanted to mount it. I was a little suprised the bracket was plastic when I received it, but still worked great. A friend made 2 mounting brackets from a flat bar, cutting and bending them to the length and angle we needed. Drilled holes and mounted them under the rear fender. Mounted the license plate bracket on the other ends of the custom brackets and wired it in for lights.

Matches lights perfectly with the original lenses of my trailer.

Easy ordering, fast shipping! Product is exactly what I needed!

LIGHT WAS EXACTLY WHAT I WANTED...WORKS GREAT!

I had to replace a side marker light on my 2015 trailer. I am the second owner and have had it for eight years. It came equipped with Optronics lighting all around, but one side marker had three of the six LED's out. So I replaced it with the same Optronics lamp. I have always had good results with Optronics and this is the first time I have seen a partial failure. No big deal. Replaced in kind and hopefully I won't have to worry about it again. They make good products and I would continue to purchase this brand.

I order a lot of stuff from Etrailer. I like the fast prompt delivery. I have however had two of these lights break the wires off right where they come out of the housing. Not long after installation. The wires were not hanging either.

Light was the same size as previous one on EZ Loader boat trailer. Easy to install and very bright. Original one made it 10 years and had moisture inside causing most of the LEDs to stop working.

This light is a good replacement on my 10 year old boat trailer. Several lights were out on the original equipment light, probably due to it being half full of water. Wires and mounting holes matched exactly which made installation easy.

I have 3rd set of optronics on one boat trailer and the second set on the other boat trailer. In the past year the boats were launched a total 12 times. These newer sets with the coated circuit boards and the 'lite pipes' are working better but not perfect. I have a few LEDs 'out on each side on each trailer. We lived in hope but I guess this is the best we can expect? Thanks Tom

Easy to apply - very visible

Very good product. Went on easily and really sticks great. Looks fantastic too.

It was an exact replacement and workded fine.

Thus far a good light, I am using it as a rear foglight on my truck. It's been surviving the Florida rains, time will tell how it holds up to the elements, I'll write a follow up during our foggy season here. It's a bright light, not too large. My use may be unorthodox, but in the couple of weeks since I installed it still tests good.

A perfect replacement for the one I broke and so cheap!

This one is for the “driver” side. It has the lens on the bottom for lighting the license plate. (It does not include the license plate holder. I like this one because you just push in the wires. I recommend this light.

I bought a couple more of these two-diode LED clearance lights to add some more lighting to the rear of my kayak trailer. They work nice and are easy to install in 3/4" holes that I drilled through a piece of aluminum angle. The trailer has orange clearance lights on the front sides, red clearance lights on the back sides, the stop/turn/parking lights on the back, three red clearance lights on the back, and a white LED license plate light. It's really lit up and very visible at night from the rear and sides. Thanks to etrailer.com for great products and services! My wife and I like to kayak, but we don't like to deal with putting our kayaks on roof racks on the top of a car. So I bought a used Load-Rite trailer that was designed to hold one Jet Ski, and added a frame made of slotted angle and 2x6 lumber to hold the kayaks, and a cargo box from Tractor Supply to hold kayak seats, life jackets, towels, sun-protection clothing, and some spare gear (ropes etc), and bought all new LED lighting from etrailer.com. The paddles are too long for the cargo box so they have to go in the car! The kayaks are tied down to the trailer with several ropes front and rear, so there is a lot of safety factor in the design....I don't worry about the kayaks coming off the trailer! The entire rig works great....when we return from a kayak trip we just back the trailer in the barn and it's ready to go for our next trip. I put a 5" diameter wheel on the trailer just behind the hitch so I can push it around on flat level surfaces. See the pictures.

Great addition to the basic, rear brake lights of a camp trailer. I added these LED RED to the brake/turn function, within the existing, small holes in the rear bumper--much more apparent when stopping/turning. These sealed LED lights are very common on larger trucks and trailers now. Easy to install and very robust assembly...priced right!