See what our Experts say about this Draw-Tite Trailer Hitch Ball Mount

• Torque Specs for the Draw-Tite Ball Mount for 2" Hitches
  Hey Frank, 2" hitch balls like what you see on the Draw-Tite Ball Mount w/ 2" Ball for 2" Hitches # DT49MR should be torqued to 250 ft. lbs. This shank come pre-torqued though, so you shouldn't have to worry about that. If there is something else I can help you with, please feel free to leave a comment and let me know!
  view full answer...
• What Parts do I Needed for a 2011 Lexus LX 570 to Tow a Cargo Trailer With Brakes?
  Hello Kenneth, Looks like you were on the right track with the wiring. The Hopkins Plug-In Simple Vehicle Wiring Harness # HM11143910 is going to get a 7 way, and 4 flat on the back of the 2011 Lexus LX 570. After reading the reviews, it looks like there are connectors on both the passenger and driver side of your vehicle. You will need to connect to the the ones on the driver side. One of our awesome customers was kind enough to share a picture of these connectors, so I went ahead and...
  view full answer...
• Will The Draw-Tite Ball Mount DT49MR Fit A 2025 Tesla Cybertruck With A 2" Hitch Receiver?
  Hello William, thanks for reaching out. The Draw-Tite Ball Mount # DT49MR can work with virtually any 2" receiver, so I see no reason why it would not work with the 2" hitch on your Cybertruck. Looking at pictures of the Cybetruck hitch online it does not appear to be recessed behind the bumper or anything. You will just want to be sure the 2" drop allows you trailer to tow level so as long as you can verify that you can be sure the ball mount will work. What kind of trailer are you pulling?
  view full answer...
• Availability of Ball Mount in Rise Position with Pre-Torqued Ball
  Hey Tom, I wish we had a way to do that but we don't have an option to order the Draw Tite ball mount # DT49MR pre-torqued in the rise position but we do have some similar options: etrailer ball mount part # e38NR with a rise of 2-3/4inches Curt # C45155 rise of 2-1/4 inch Curt # C45152 rise of 2 inch
  view full answer...
• Draw-Tite Ball Mount DT49MR - What Is The Distance From Hitch Pin Hole To The Center Of The Ball?
  Hello Omar, thanks for reaching out. For the Draw-Tite Ball Mount w/ 2" Ball # DT49MR, the distance from the center of the hitch pin hole to the center of the ball is 8-1/2". Will this work for you? What is the "do not exceed" spec your car lists? Let me know and I am happy to look into it and see if we have anything!
  view full answer...
• Recommended Trailer Hitch for a 2023 Chevy Trailblazer
  Gerald, it sounds like you're looking for a Draw-Tite hitch for your 2023 Chevy Trailblazer. If this is the case, then you can use the Draw-Tite Max-Frame Trailer Hitch Receiver # DT55GR. This hitch has a max weight capacity of 3,500 lbs, a max tongue weight of 525 lbs, and has an easy bolt on install using the included hardware. If you plan on towing with your Trailblazer, you're also going to need a ball mount # DT49MR and wiring harness like the T-One Vehicle Wiring Harness with 4-Pole...
  view full answer...
• Recommended CE Smith Trailer for Brooklyn 14.0 Pro Tandem Pedal Kayak PK14
  Hello Carol, I also love to fish, so I don't blame you for wanting to get off the banks. The CE Smith Multi Sport Plus Boat and Kayak Trailer w/ Bunks - 12" Wheels - 14' Boat - 800 lbs # CE48870 will work great for the Brooklyn 14.0 Pro Tandem Pedal Kayak PK14. I went to their webiste and checked out all the specs. This trailer can handle Kayaks up to 14 feet long, so that puts you at the limit for the length. The width is 54" so that gives you plenty of wiggle room. To be able to hook...
  view full answer...
• Portable Winch Solution for Master Lock Electric Winch
  We haven't carried that winch in some time but it was one that doesn't fit standard hitch winch mounting plates. Instead it was designed to attach directly to a hitch ball for an even easier portable type solution. So you could just bring a ball mount with you like the # DT49MR and it would be just as portable if not more.
  view full answer...
• Should Ball Mount Be Flipped In Rise Position for 2004 4Runner Towing Winnebago
  Hey Dave! Although we don't carry the 21536 the Draw-Tite Ball Mount # DT49MR is almost identical. This has a 2" drop and a 3/4" rise when flipped over. Flipping the ball mount into the rise position will keep you close to/right at level with the little bit of rear sag you're experiencing. Any big trips coming up with your Winnebago?
  view full answer...
• Looking for Longer Ball Mount Hitch that has 2 inch Drop
  Hey Paul, we have exactly what you are looking for with the Convert a Ball part # AMSC2. This has a 2 inch drop, fits a 2 inch hitch and also is 9-1/2 inches from the center of the hitch pin hole to the center of the ball hole.
  view full answer...
• Comparing Trailer Hitches For A 2021 Jeep Grand Cherokee L
  For your 2021 Jeep Grand Cherokee L, we have two options. We have the Curt Trailer Hitch Receiver # C97JR, and the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit # DT42GR. Both of these hitches offer a 7,500lbs maximum GTW and can be used with a weight distribution system, however, the Draw-Tite # DT42GR has a tongue weight that is rated 375lbs higher than # C97JR. So if you're after the hitch that has the highest ratings, then # DT42GR is what you want. Although, you won't have...
  view full answer...
• Will Draw-Tite 2 Inch Ball Mount Rattle Around in Hitch Receiver Opening
  Every hitch and drawbar will have some movement between them, it's unavoidable. Any manufactured product like a receiver hitch will have variances in its size. For instance, the Curt # 14090 Class IV hitch has a 2 inch receiver. The actual measurement of the inside of the receiver tube is usually a little larger than 2 inches. The outside dimension of the shank of a ball mount like the # DT49MR you'd looked like is typically a tiny bit smaller than 2 inches. If the inside dimension of...
  view full answer...
• What Hitch and Ball Mount do You Recommend for My 2022 Subaru Outback Wagon?
  For towing with your 2022 Subaru Outback, a great hitch is the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - 2" # DT73RR. Not only does this hitch offer the greatest available weight capacity we currently carry for your vehicle, it also comes with an easier installation. All of our other hitches require you to remove the impact beam from the bumper. By avoiding this, the installation of the # DT73RR does not take as much effort. As far as the ball mount, it really depends on...
  view full answer...
• Does the Draw-Tite Ball Mount DT49MR Come With Hitch Ball
  Yes, the Draw-Tite Ball Mount part # DT49MR comes with a pre-torqued 2" hitch ball as well as a 5/8" diameter hitch pin and clip. It comes ready to go and use.
  view full answer...
• Ball Mount, Ball, and Hitch Pin to Use with Curt Hitch that Fits 2018 Subaru Outback Wagon
  When we had the Curt hitch # C13410 installed on a similar 2018 Subaru Outback Wagon as yours we found that from the top of the hitch opening down to the ground measured 15-1/2 inches. Since most trailer that your vehicle would tow would have a coupler height a couple inches shorter than that I would go with the Draw Tite ball mount part # DT49MR which has a 2 inch drop. This comes with a 2 inch ball which is a very common as well as a pin and clip to secure it.
  view full answer...
• What Ball Mount and Coupler Is Needed For CE Smith Multi Sport Plus Boat and Kayak Trailer CE48870?
  The CE Smith Multi Sport Plus Boat and Kayak Trailer # CE48870 has a 2" ball coupler. It also requires a 4-way flat connector on your tow vehicle to operate the tail lights. The coupler has a height of 14" so you will need to ensure your ball mount has the correct amount of drop to tow level. If you measure the height to the inside of your receiver I can help you find the correct parts. The Draw-Tite Ball Mount w/ 2" Ball # DT49MR has a 2" drop and would fit with a 16" receiver height.
  view full answer...
• Trailer Hitch And Wiring For A 2019 Tesla Model X
  For your 2019 Tesla Model X, we have the Draw-Tite Max-Frame # 76143. This is a class III hitch capable of towing up to 5,000lbs GTW, and 750 maximum TW. If you need wiring, I recommend the ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit # 119250KIT. This kit is plug-n-play into your factory harness, alleviating all cutting and splicing. Finally, if you need a ball mount, I recommend the Draw-Tite Ball Mount # DT49MR. This kit comes with...
  view full answer...
• What Is The Ball Height Of The Stealth Hitch SH62VR On A 2023 BMW X3
  We got our hands on a 2022 BMW X3 and successfully installed this hitch # SH62VR. The hitch height was measured at 13" from the ground to the top inside edge of the receiver. The ball will sit about 2" above that. You are correct, this ball is a fixed height. You CANNOT use the stealth hitch receiver with other ball mounts like # DT49MR for example. The stealth hitch receiver is not made for towing, and you must use the stealth hitch ball only. I am not sure what trailer you have, but...
  view full answer...
• What Trailer do You Recommend to Transport My Emojo Caddy E-Trike and Additional E-Bike?
  I have a great transporting solution for you. I did some research on your Emojo Caddy Pro E-Trike, and we unfortunately do not have an option for this trike that will support the 90-pound (with battery) weight and allow you to mount your other e-bike. However, the best option to transport the Emojo Caddy along with your other e-bike is the Detail K2 Mighty Multi A-Frame Utility Trailer - 7-1/2' Long # K2MMT5X7. The great thing about the Detail K2 Mighty trailer is that you can use the gate...
  view full answer...
• Ball Mount and Hitch Ball for Towing a U-haul Trailer
  The Draw-Tite Ball Mount w/ 2" Ball for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs item # DT49MR you were looking at would work great to haul a 6 x 12 uhaul trailer. The trailer has a maximum 4,400 lbs capacity which would not exceed this ball mount and balls capabilities. If you are going to be towing regularly, I recommend the Curt Towing Starter Kit for 2" Hitches item # C45534. This towing kit will provide you with a 2" ball and a fixed ball mount with a 3/4" rise and 2" drop. It...
  view full answer...
• What Do I Need To Hook Up A Boat Trailer To My 2021 Ford Explorer
  I can definitely get you set up to tow a boat trailer with your 2021 Ford Explorer. You will need a few things for this setup: a hitch receiver, a ball mount, and a 4-way wiring harness. The first thing you will need is a hitch receiver. I recommend the etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2", part # 76320. This hitch receiver has a maximum tongue weight of 600 lbs and a maximum gross trailer weight of 6,000 lbs. Once you have the hitch receiver,...
  view full answer...
• Recommended Hitch Set-Up for a 2018 Acura RDX
  The Draw-Tite # 75784 will include all the hardware needed to get installed. This will require no drilling or trimming to get installed and will bolt directly to the frame of your 2018 Acura RDX. From here there will be a few parts needed depending on what you will be using the hitch for. If you will be towing, you will need a ball mount, ball, and pin/clip to hold them in place. Something like the Draw-Tite Ball Mount w/ 2" Ball for 2" Hitches - 3/4" Rise, 2" Drop # DT49MR will include...
  view full answer...
• Can You Flat Tow a 2020 Honda CR-V With a CVT Transmission
  The 2020 Honda CR-V Touring models are equipped with CVT style transmissions and should not be flat towed. I recommend using a tow dolly like the Roadmaster # RM-2050-1. It has a 4,250 pound capacity and adjustable tracks for the wheels on the CR-V. You would need a standard ball mount with a 2 inch ball to connect the tow dolly to the towing vehicle # DT49MR and a brake controller to activate the electric brakes. I suggest the Tekonsha Prodigy P3 # 90195, but you will need to contact...
  view full answer...
• Can Ball of Draw Tite Ball Mount DT49MR be Mounted on Rise Side
  Hey Scott, when you get the Draw Tite ball mount part # DT49MR you can swap the ball to be on the rise side of the ball. We get the ball mount with the ball pre-installed and don't have a way to swap it before shipping. We don't have any pre-installed ball mount options that have it on the rise side currently.
  view full answer...

Do you have a question about this Trailer Hitch Ball Mount?