Wheel Studs and Chrome Lug Nuts Recommendation to Replace 2002 Tracker Trailstar Studs

Question

Question:

Looking for the right size wheel studs. This is from a 2002 Tracker Trailstar Trailer. Stud Size as close as I can measure Thread Diameter A 0.5 Stud Length B 1.75 Spline Length C 7/16inch or 0.437 Base Length D 5/8inch or 0.625 Spline Diameter E 9/16inch or 0.56inch 0.54 Overall Length 2 Thread Length 1.13 Also looking for Chrome Trailer Lug Nuts 60 degree 1/2inch -20 to match these studs. Total 12 each 5 each side and 2 spare Thanks

asked by: Ken P

1

Helpful Expert Reply:

Based on the dimensions you listed it looks like the part # K12WB2 is the closest match. This might be slightly longer but should still work. I attached a picture that has all of the dimensions listed.

For chrome 60 degree lug nuts you would then want the part # 12CLN.

expert reply by: Jameson C

1

click to enlarge

Answer 1

The Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 5-1/2 #AKHD-555-35-K will fit the spindle on your trailer to replace your AL-KO 8700 hub, but this does have a 5 on 5-1/2" bolt pattern. My information is the AL-KO…

view full answer...

Answer 2

There are really two reasons to replace a grease seal, if they are damaged or worn and leaking grease then that is an obvious factor. If you are replacing bearings it is usually best to replace the grease seals as well because although they may still…

view full answer...

Answer 3

Hi Lane, The closest option we have to the measurements you provided would be the DeeMaxx Drive-In Wheel Stud - 1/2" Diameter x 2" Long #DE52GR.

view full answer...

Answer 4

Yes, as long as the spare tire is the same size, load range (weight rating) and has the matching wheel bolt pattern you can use a bias ply spare to replace a radial main tire for the short distance you'll travel to get the radial repaired or…

view full answer...

Answer 5

We don't have exact specs on the part that you're referring to, but I do know that's a stamp on a UFP hub, so I was able to reach out to my tech contact at Dexter UFP and he said that most of the hubs that number would be stamped on use a…

view full answer...

Answer 6

First, the DOT date code on a tire is 4 numbers. The first 2 are the week and the last 2 are the year. So for example if it was 2314 that means that tire was made in the 23rd week of 2014. There isn't a difference between a tire sitting on the…

view full answer...

Answer 7

It sounds like you have a different size axle than anything we carry. The closest we have is the Dexter Trailer Axle w/ Electric Brakes - E-Z Lube - 6 on 5-1/2 Bolt Pattern - 86-1/2" - 5.2K #8327816-EB which has spring centers at 71-1/2 inches…

view full answer...

Answer 8

The closest option we have and what will work for your application is the Kodiak Wheel Bolt - 1/2" Diameter x 1-11/16" Long #K12WB169. This has a slightly longer knurl, the correct threading and are just slightly shorter at 1.6875 inches.

view full answer...

Answer 9

We have the part #DX98FR which is 1/2 inch longer than the #K12WB2 that you referenced and is same 1/2 inch diameter.

view full answer...

Answer 10

Hey Larry, I would recommend going with a stainless steel lug nut like the part #LHLR103 that matches the specs you need. Stainless steel won't rust or corrode. This means they won't swell up either making it hard to fit a socket on.

view full answer...

Answer 11

The Kodiak Wheel Bolt #K12WB169 that you referenced should fit just fine. Since all of the differences are small fractions of an inch you are good to go!

view full answer...

Answer 12

We do have a 1/2" diameter wheel bolt that is close to 1-3/4" long which may work for you. The Kodiak Wheel Bolt #K12WB169 is 1-11/16" long, but that does not take into account the lip of the bolt, as you can see by the accompanying…

view full answer...

Wheel Studs and Chrome Lug Nuts Recommendation to Replace 2002 Tracker Trailstar Studs

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching