Replacement Grease Seal for Dexter 3,900 lb Axle

Question

Question:

i am looking for axle hub grease seals . what i have is a dexter axle #9747800 it says a capacity of 3900 lbs thanks for your help

asked by: Greg A

0

Expert Reply:

According to Dexter your axle uses a 10-19 grease seal which would be the # 58846. If you need a pair you can use part # RG06-050.

expert reply by: Robin H

0

Answer 1

Hey Bill, Sorry for the huge wait, I finally got confirmation on your axle from Dexter that it was indeed a #10 and was able to determine that the Torflex Lift Kit - Tandem Axle #K71-707-02 would be the correct fit. I've attached a short video…

view full answer...

Answer 2

I sure can Mark and thanks for the information! The Dexter 3,900 lb torsion axles use the same bearings as 3,500 lb axles. Which means the correct replacement bearing kit is the item #BK2-100 you were looking at. You'll need one set per hub. Your…

view full answer...

Answer 3

Hey Thomas, thanks for reaching out! According to my research your 3,900 lb axle should use the same bearing parts as a 3,500 lb axle so you should need the Hub Bearing Kit for 3,500 lb with #84 Spindle #BK2-100. This uses an L68149 inner bearing, an…

view full answer...

Answer 4

Though I can confirm that InTech does use Dexter torsion axles, I was unable to find exactly which one and what angle is used on your 2020 Sol Dawn. So with that being said, what you will need to do is contact InTech with your VIN and they should be…

view full answer...

Answer 5

On Dexter 12" Nev-R-Adjust Electric Brake Assembly #23-458 the shoe pad thickness is 3/16 of an inch. Dexter says that you should replace the shoes if the material gets down to 1/16 of an inch thick or less.

view full answer...

Answer 6

For your propane tank with fill valve, you most likely need the Camco Horizontal 2-Stage Propane Regulator w/ P.O.L - 160,000 Btu/Hr #CAM59333. This will have the 1/4 inch NPt inlet and the 3/8 NPT outlet and will maintain a constant 11 inch water…

view full answer...

Answer 7

Yes, there are spacers that can be used with the Timbren #TGMRTTK30 kit on your 1987 GMC Pickup with a 2-1/2" lift. We recommend using two of the 1" spacers #TA25723-90AD00 on each side. The idea is to have a 1/2" to 1-1/2" gap…

view full answer...

Answer 8

The Dragon's Eye LED Clearance or Side Marker Light #DG52440VP goes beyond a 180 degree view. As you can see on the image below you can see the amber color projecting back onto the trailer surface it is mounted on.

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Replacement Grease Seal for Dexter 3,900 lb Axle

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching