Wiring Diagram Tekonsha Voyager Brake Controller # 39510

Question

Question:

I need a wiring diagram for a tekonsha voyager electronic brake control can some one please help me?

asked by: Russell

0

Expert Reply:

Yes we can help. To the right there is a picture that has a diagram of how most brake controllers wire up, if you click it you will be able to see an enlarged version of the picture. Below you will find a link to the installation instructions and to wiring instructions for wiring brake controllers. All brake controllers wire pretty much the same with a white ground wire, a black power wire a red brake switch wire and a blue brake feed wire that goes to the trailer brakes.

If you would like to give some information about your vehicle, I could make a more specific recommendation on how to wire it and let you know if any other parts are needed. I would need the year, make, and model of your truck along with the type of trailer connector you have at the rear of the vehicle.

expert reply by: Robert G

0

click to enlarge

John T.

1/29/2013

I have a 2006 chevy suburban equipted w a trailer package, I have the wiring harness to install on to my Tekonsha voyager brake controller. The problem I have is there are 5 wires on the wiring harness and only 4 on the controller. Wiring harness Dk.Blue - trailer brake controller switched outputRed - Fused trailer brake controller battery feedBlack - Brake controller groundLt Blue - Vehicle stop lamp switch to brake controller input Brown - Brake controller illuminationcontroller wires Red, white, blue, and blackplease let me know what wires go where. ThanksJohn

Patrick B.

2/8/2013

With your 2006 Suburban, you should have a plug-in port that you can use with part 3015-P so that you do not have to splice wires or use the factory included pigtail. This will simplify the whole installation. If you do not want to use the plug in harness, the splicing operation is still pretty simple. You would make the following connections. Truck Wire - Function - Brake Control Wire Dk. Blue - Brake Ctl Ouptut - Blue Red - Fused Battery Feed - Black Black - Brake Ctl Ground - White Lt Blue - Vehicle Stop Lamp - Red Brown - Illumination - Not Used

Answer 1

That is the only way you'd be able to install the Tekonsha Prodigy P3 Trailer Brake Controller #90195 on your 2023 Ford Transit T350 since there is no custom fit wiring harness. To install this, you'll first need to find the cold side of the…

view full answer...

Answer 2

I have attached a basic brake controller wiring diagram for you. You will want to make sure that you ground the white wire to the negative post on the battery. The black wire will attach to the positive battery post. The red wire will tap into the…

view full answer...

Answer 3

Yes, it will Bob. The Dometic RV LP Gas Furnace item #DMC64MR is also a 35,000 btu furnace that heats with LP gas and 12V power. It measures 20" deep x 7" tall x 16-1/2" wide. It can be installed in a horizontal or vertical…

view full answer...

Answer 4

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 5

So the lifespan and when to change a lube plate doesn't have a hard and fast answer because there are numerous variables associated with how long it will last. The terrain you are going over, the weight of your trailer, and the frequency with…

view full answer...

Answer 6

If you do not already have a 4-Way flat connector at the rear of your 1970 GMC C30 then you will want to start off by installing the Tekonsha 4-Pole Hardware Kit #18252. This will simply splice into your current light functions. I have attached a…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

It sure will! A brake Controller isn't a vehicle specific item, you can install a brake controller in just about any vehicle. To swap the controller back and forth, you'll need a #7894 pigtail and a #TK5906 Replacement mounting bracket kit.…

view full answer...

Answer 9

Manufacturers can use any colors they want since there isn't really a standard for wire color and function. You will need to test each of the wires using a circuit tester such as #PTW2993 to determine the functions. Then you can attach them to…

view full answer...

Answer 10

It sounds like you have everything wired correctly to bench test. To bench test a brake controller you need to connect the black wire from the Tekonsha Voyager Trailer Brake Controller #39510 to the positive terminal of a 12 volt battery and the…

view full answer...

Answer 11

On your 2002 Ford F-250 you will need to connect the Red wire to the Black wire on the brake controller for +12 Volts power and the Light Green wire to the Red Stoplight wire on the brake controller. The Dark Blue wire is connected to the Blue wire…

view full answer...

Answer 12

Thank you for all of the information and pictures! It looks like you should at least have some wiring already run on your 2019 Chevy Express Van 3500 so I'm just as confused as to why you don't have a round plug with a cap inside the…

view full answer...

Wiring Diagram Tekonsha Voyager Brake Controller # 39510

Featured Help Information

Miscellaneous Media

Continue Researching