Should Grease be Used to Fill Space Inside After Hub Installation
Updated 12/27/2021 | Published 12/24/2021
Products Featured in This Question
Question:
I ordered the pre-greased hub and installed it. It is great but i noticed there is more space inside Do I need to add more grease to fill it up? These is some play when is hub is installed. After putting on the cap, should I fill it completely up?
asked by: Patrick C
Expert Reply:
When installing your Easy Grease Trailer Idler Hub Assembly for 2K Axles - 4 on 4 - Pre-Greased # AKIHUB-440-2-EZ-1K there should not be any "play" or space. Since it is pre-greased, more grease is not needed. I recommend checking your spindle to make sure this hub is correct. It uses a # L44643 inner and outer bearing, so your spindle should measure 1" where both bearings ride.
I have attached a helpful article on replacing/packing bearings, as well as a video showing the process and what your hub should look like when it is on the spindle.
Product Page this Question was Asked From
Easy Grease Trailer Idler Hub Assembly for 2K Axles - 4 on 4 - Pre-Greased
- Trailer Hubs and Drums
- Idler Hub
- EZ Lube
- L44643 / L44643
- Standard Grade
- For 2000 lbs Axles
- 1/2 Inch Stud
- 4 on 4 Inch
- 8 Inch Wheel
- 10 Inch Wheel
- 12 Inch Wheel
- 13 Inch Wheel
- 14 Inch Wheel
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: 370014
- Search Results: 010~036~00
- Search Results: 9~28~1
- Search Results: timbren vehicle suspension
- Search Results: spare tire mount
- Shop: Timken Grease and Oil Seal - Double Lip - I.D. 2.250" / O.D. 3.376" - 452920/482920
- Shop: Timken Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Dexter Nev-R-Adjust Electric Trailer Brakes - 12-1/4" - Left/Right Hand Assemblies - 15K
- Shop: Oil Seal
- Shop: Dexter Trailer Brake Drum for 12,000-lb and 15,000-lb Axles - 12-1/4" x 5" - 8 on 6-1/2
- Shop: Kodiak Disc Brakes - 13" Hub/Rotor - 8 on 6-1/2 - Dacromet - 7,000 lbs - E-Z Lube
- Shop: Unitized Oil Seal
- Video: Timken Bearing Kit Installation - Enclosed Trailer
- Video: A Closer Look at the Timken Bearing Kit for Lippert, Dexter, and AL-KO Axles
- Shop: Vehicle Snow Plows
- Q&A: Recommended Spare Tire Carrier That is Not Angled Upwards
- Shop: Suspension Enhancement
- Shop: Trailer Wiring
- Shop: Brake Controller
- Video: Trailer Axle with Idler Hubs Spec Review
- Video: Tekonsha BRAKE-EVN Trailer Brake Controller: The Breakdown
- Video: 2012 Chevrolet Express Van Tekonsha Prodigy P2 Trailer Brake Controller: Complete Installation
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Search Results: 40 amp circuit breaker
- Search Results: fuse tap
- Shop: Trailer Hitch
- Q&A: Should a Trailer Hub Be Completely Filled With Grease After Being Installed On Spindle?
- Q&A: Replacement Grease Seals for Dexter Part # 010-036-00 on a 7,000lb Trailer Axle
- Video: Breaking Down the Kodiak XL ProLube Kit for for 5,200-lb to 6,000-lb Axles
- Q&A: Replacement Bearing Grease Seal for Dexter 010-036-00
on Trailer Hubs and Drums
