Ramp that Can Help Get E-Bike into Truck Bed

Question

Question:

How can I get an electric mt. bike up and onto a Yakima HighRoad roof rack which sits across my tonneau cover on my F-150. I know I need a ramp - any ideas?

asked by: Rich B

0

Expert Reply:

A motorcycle ramp like the part # 288-07452 would be a great option to help get the E-bike up into the truck bed so that you wouldn't have to lift the bike as high to get it onto the bike rack you have mounted to the crossbars.

expert reply by: Jameson C

0

click to enlarge

Answer 1

We have bike racks like the can attach to the top of a hard tonneau cover like the very cost-effective Hollywood Racks Truck Bed Bike Carrier #HRT970. This is a bolt-on product that holds your bike at the fork that would require you to drill through…

view full answer...

Answer 2

The Replacement Ramp for Yakima OnRamp Electric Bike Racks #Y99KR is designed to be used directly with the Yakima OnRamp e-bike rack 8002706 & 8002707, however if the width of your wheel trays on your Buzz Rack Scorpion H2 is 2-1/2" wide…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Hey Adam, yes the Air Lift kit part #AL57388 does fit your 2021 GMC Sierra 1500 AT4 Alpine Rocky Ridge Edition. Are you wanting a compressor kit too?

view full answer...

Answer 5

Hello Barry, Since you already have a weight distribution (WD) hitch and are only experiencing a little rear sag, I recommend going with SumoSprings. I typically only suggest Timbrens for those who are towing heavy loads regularly, as they can create…

view full answer...

Answer 6

There are a number of differences between the Firestone Ride-Rite Air Helper Springs #F2445 and Air Lift LoadLifter 5000 Ultimate Air Helper Springs #AL88299, starting with fit. While the Air Lift will fit all models of the 2018 Toyota Tundra, the…

view full answer...

Answer 7

Hi Brian; the SumoSprings #SS45FR will not fit your 2025 Sierra 1500 with Adaptive Ride Control. The answer from Sam is a little older and probably written before anyone knew about the restriction. I went ahead and corrected it, thank you for…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hello David, thanks for getting in touch. The 2019 GMC 1500 AT4 has a 2" lift, and the #AL88388 kit you mentioned has taller brackets to fit the 2" lift. I looked up the X31 model and it does say it has offroad suspension, but it didn't…

view full answer...

Answer 11

Hi Bill; I'm not surprised the #T53MR gives you a rough ride since it is the severe service kit. Timbren SES isn't overly forgiving to begin with, and this particular design is for constant loads like a slide-in camper. I would recommend the…

view full answer...

Answer 12

Firestone doesn't but Air Lift does. The Air Lift LoadLifter 5000 Ultimate Air Helper Springs item #AL88288 are the closest comparable option and the only ones compatible with the 3.0 diesel engine in the 2020 Chevy Silverado 1500. These also…

view full answer...

Ramp that Can Help Get E-Bike into Truck Bed

Product Page this Question was Asked From

Continue Researching