Replacement Bearing Kit for 2000 Viking Pop Up Camper with L44649 Inner and Outer Bearings

Question

Question:

I have a 2000 Viking pop up camper, MOdel number is 2107. it is rate 2000 pd axle and made by Dexter. The maual says the inner is L44610/L44649 and outer is the same as above, could you now tell me what kit I need?

asked by: Tom

1

Helpful Expert Reply:

If both your inner and outer bearings are # L44649 then the correct replacement kit is # BK1-150.

expert reply by: Charles S

1

click to enlarge

Answer 1

The mounting bolt pattern of the Buyers Products A-Frame Jack #3370091265 is 3" all the way around. The mounting holes are elongated though so if you have a slightly larger/smaller distance it should still work out.

view full answer...

Answer 2

Thank you for getting me all of the info you shared from your hub. Based on that we know that the #8-259-5UC1-EZ that you referenced is correct for both sides of your axle.

view full answer...

Answer 3

Hey Shane, The hub face extends past the studs on the Trailer Idler Hub for 2K Axle AKIHUB-545-2-Z by 3/4" so you'll need to switch to a smaller option like the Dexter Trailer Idler Hub Assembly #8-259-5UC1-EZ. This hub face only extends…

view full answer...

Answer 4

Thanks for the pictures. Either part number hub is going to fit your hub since they both have the same bolt pattern and bearings. The difference is going to be based on the diameter of your trailer wheels. If you have 13-14 inch diameter rims you…

view full answer...

Answer 5

To choose a compatible hub assembly for any spindle the key is knowing the inner and outer bearing part numbers, or if they are not available, precise dimensions of the spindle at the points where the bearings and grease seal ride. These points on…

view full answer...

Answer 6

Can you get me the diameter of the axle or the capacity if you can find it? Most likely it's a 2k axle and the kit part #BK1-100 would be the correct kit to use but I'd need to verify that for sure. The correct diameter axle for a 2k axle…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hey James, you can go with a 4k axle leaf spring like the part #e22YR in place of what you have now while it has a slightly higher weight capacity it's not enough that it would create a harsh ride quality. This is a 26 inch long spring though so…

view full answer...

Answer 10

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 11

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 12

Hey Vernon, great to hear from you again! For your trailer that has a GVWR of 11,295 lbs I actually recommend stepping up one level and going with the 18.5K #WS49MR which has the same 6" drop and fits a 2-1/2" hitch receiver like the 12.5K…

view full answer...

Replacement Bearing Kit for 2000 Viking Pop Up Camper with L44649 Inner and Outer Bearings

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching