Mounting Bolt Hole Pattern for the Buyers Products A-Frame Jack # 3370091265

Question

Question:

What is the bolt pattern of the jack....

asked by: Philip M

0

Expert Reply:

The mounting bolt pattern of the Buyers Products A-Frame Jack # 3370091265 is 3" all the way around. The mounting holes are elongated though so if you have a slightly larger/smaller distance it should still work out.

expert reply by: Jon G

0

click to enlarge

Answer 1

The A-Frame Trailer Jack - Topwind - 5,000 lbs. by Dutton-Lainson #DL22772 does not have a grease zerk fitting integrated, sor do any of our other top wind jacks. This doesn't mean they are difficult to maintain, but they do not have that…

view full answer...

Answer 2

Hi Robert; I'm assuming you mean can the #DL22772 use a drop leg that would adjust up and down. If you can find one that fits and matches the capacity then yes, you could use a drop leg. However, we only offer a standard foot like the #DL22542…

view full answer...

Answer 3

view full answer...

Answer 4

There are some Dutton-Lainson trailer jacks that are made in the USA as well as a few that are not. Any jacks that we carry that are made in the USA have that as part of the description to help set them apart. Currently we have the following options:…

view full answer...

Answer 5

The closest equivalent manual jack, to the Lippert item #LC285318, would be the Buyers Products A-Frame Jack w/ Support Foot - 15" Travel - 5,000 lbs item #3370091265. This jack has the standard A-Frame jack 3" diamond pattern. I have…

view full answer...

Answer 6

A trailer jack only lifts part of the weight of the trailer and not the whole 10,000 pounds of your trailer. A 10K trailer would have a tongue weight of around 1,000 to 1,500 pounds. But the higher the capacity of the jack the easier it is for the…

view full answer...

Answer 7

I went out to our warehouse to take a look at the Buyers Products A-Frame Jack #3370091265 referenced in your question. I measured a height from the mounting bracket up to the top of the tube (before the handle) of just about 9-1/2 inches. I have…

view full answer...

Answer 8

For your 10,000 lb car hauler trailer, I recommend the Round A-Frame Trailer Jack - Sidewind - 15-5/8" Travel - 5,000 lbs #TJA-5000S-B for a manual jack, with footplate #JF-99. The majority of the weight of your trailer will be on your axles and…

view full answer...

Answer 9

The mounting hole dimensions of A-frame jacks are a standard 3 inches apart on center, so you will need to weld your new jack on. I highly recommend the etrailer Round, A-Frame Jack #TJA-5000S-B, which has a 5,000 lb capacity and will give you…

view full answer...

Answer 10

The Round A-Frame Trailer Jack #TJA-5000S-B has mounting holes that are elongated. The actual holes are 3/4 inch long and 7/16 inch wide. That gives you a minimum of 2-1/2 inches or maximum of 3-3/4 inches to the nearest or farthest part for…

view full answer...

Answer 11

Hey Craig, thanks for reaching out! I believe the Optronics Fleet LED Trailer Tail Lights w/ Grommets #TLL12RK will work as replacements for your 2008 Featherlite 4926 trailer, but you'll need to confirm this on your end. These lights carry the…

view full answer...

Answer 12

The light dimensions of the Optronics LED #TLL12RK are 7-9/16" long x 2-3/4" tall x 1-3/4" deep and the hole size needed is 6.75" by 2.5 inches. I confirmed this with my contact at the manufacturer and I've attached a template…

view full answer...

Mounting Bolt Hole Pattern for the Buyers Products A-Frame Jack # 3370091265

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching