Landing Gear Recommendation for 2010 Jayco Designer 35 RLTS

Question

Question:

I have a 2010 jayco designer 35 rlts 5th wheel. I need new landing gear. The tubes are flat on top and measure 36 1/2inch with 15 1/2inch between blocks. I cant find a replacement anywhere. HELP

asked by: Paul H

0

Expert Reply:

The standard measurement on landing gear legs is 15-1/2 inches between the tabs that are on the actual legs like what you have.

The etrailer Landing Gear Set, part # RVLG-8000 can be used to replace the landing gear set you have on your 2010 Jayco Designer as it fits the standard dimensions you have.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Hey Frank, since Atwood is no longer in business we can't get replacement legs for their setups which means your best option is to replace everything like with the Lippert #LG-4 that you referenced. We do know that the Lippert kits do fit the…

view full answer...

Answer 2

We do have motors that you can add to your landing gear. For example, the Landing Gear Set #RVLG-8000 can be operated with the manual crank #RVLG-HDL but you can also add the motor #LC142178 and switch #LG-145236 for effortless operation on your end.…

view full answer...

Answer 3

Landing gear legs #LG-179014 and #LG-179013 may have slightly different dimensions from the OEM units they replace but these parts are usable replacements for the popular LG-1, LG-3, and LG-183708 landing gear sets. Part 71488 was made by RBW which…

view full answer...

Answer 4

Thanks for sending a picture. Although it might be possible to remove the gearbox and motor while the landing gear is up and supporting weight, for safety reasons, I do not recommend doing so. In order to replace the gearbox and motor on your landing…

view full answer...

Answer 5

If the existing landing gear on your Jayco Designer is from Venture, Stromberg Carlson or Lippert, you can use the Repair Kit #LG-146059 for the Lead Jack or #LG-146060 for the Follow Jack. These kits will include all the gears and pins required for…

view full answer...

Answer 6

You can use your existing Demco 18K Hijacker auto-slide hitch in your 2015 Ford F-350 with the factory puck system in either of two ways. One way is to use the Demco 5th Wheel Rail Adapter for Ford OEM 5th Wheel Towing Prep Packages, part #DM6175.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Hey Bobby! As far as the jacks go for item #RVLG-8000 and item #RVLG-8HDL there is absolutely nothing different. The item #RVLG-8HDL comes with the manual handle that I have attached a picture of below. That is the only difference. If your 2019…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The gearbox #RVLG-RDBOX for the Landing Gear Set w/ Handle #RVLG-8HDL can be mounted in the horizontal or vertical position. I went out to the warehouse and tested both the gearbox and lead leg together and the pins that hold the gearbox in place…

view full answer...

Landing Gear Recommendation for 2010 Jayco Designer 35 RLTS

Product Page this Question was Asked From

Continue Researching