How Tight Should Castle Nut be on Trailer Hub
Question:
2005 Horton car hauler with 6000 lb. Dexter EZ lube axles. I bought this used and noticed that all 4 wheels had play in them, so when I repacked the bearings I tightened the nut enough to eliminate the play but still allow the wheel to turn freely. Using a laser thermometer, I took it out for about a 20 minute drive loaded with a car in the trailer. I noticed the hubs came up to 95-115 degrees within about 2 miles, but never got any hotter than that. The air temperature was 55 degrees, so about a 40-50 degree temp rise. Is that normal or do I have the bearings too tight?
asked by: Robert B
Expert Reply:
There is no specific torque rating for the castle nut that holds your hub in place. We recommend tightening the castle nut down until it stops, and then backing it off to the next notch wheel the tang washer will fit into the castle nut. Over tightening the nut can lead to the spindles and bearings overheating, which can damage them.
We have a video that outlines the proper way to remove and install a trailer hub, to view the video, click on the provided link.
95 degrees on a 55 degree day seems a bit warm. I would try the above mentioned install method for the nut which should reduce the tension.
Product Page this Question was Asked From
Replacement Trailer Hub Bearing - L68149
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.378 Inch I.D.
- Bearing L68149
- Race L68111
- 3500 lbs Axle
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: Proper Way to Tighten Trailer Spindle of Castle Nut
- Video: Remove and Reinstall a Trailer Hub Review
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Video: Making sure the Redarc Tow-Pro Liberty Brake Controller Fits
- Shop: CE Smith Trailer Idler Hub Assembly w/ Case for 3.5K Axles - 5 on 4-1/2 - Galvanized - Pre-Greased
- Shop: Dexter Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2
- Search Results: marine hubs
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Shop: Dexter Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2 - Pre-Greased
- Q&A: Replacement Hubs For A Pontoon Boat Trailer With 7MW-1020-976 Hubs
- Video: DIY Installation for the etrailer Galvanized Trailer Idler Hub Assembly for 2,000-lb Axles
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Shop: Brake Controller
- Shop: Trailer Spindle Nut 1"
- Video: Spindle Nut Kit for EZ Lube Axles: The Breakdown
- Shop: Suspension Enhancement
- Q&A: How Tight Should Spindle Castle Nuts be Tightened
- Search Results: trailer jack
- Video: All You Need to Know About the Electric Trailer Brake with Dust Shield
- Article: How to Raise Your Travel Trailer Height
- Article: Trailer Wiring Diagrams
- Search Results: 84546uc3~ez
- Article: Most Popular Wheel Bearings
- Search Results: 25580
- Search Results: trailer hubs and drums
- Video: Feature Breakdown: CE Smith Trailer Idler Hub Assembly w/ Case for 3.5K Axles
- Search Results: marine hub
- Video: All About the #42 E-Z Lube Spindle w/ Flange for 5.2K to 7K Trailer Axles
- Q&A: Can One Brake on Trailer Axle Be Replaced or Should Both Be Replaced
on Trailer Bearings Races Seals Caps
