Free Shipping on Orders Over $99
Custom fit Trailer Wiring for your:
Make installing a trailer wiring harness on your Chevrolet S-10 Pickup as easy as possible with a custom fit wiring harness from Draw-Tite, Curt, Pollak, Tow Ready, Bosal, or Hopkins. A custom kit will eliminate or reduce the need to cut and splice wires in your Chevrolet S-10 Pickup while helping to protect sensitive electronics.
What our customers are saying:
I was concerned when I came to your web site to make this purchase because my husband always asks for guy stuff every year at Christmas. Since I usually have no idea of what it is that Im even ordering for him, if the process becomes at all difficult or confusing, I always stop and just get a gift card which I hate to do because I feel it is impersonal. This purchase however, was so simple that I even dared to venture into the deal/clearance section where I found an additional item that I had planned to order from a different web site for a cheaper price so I ordered that too! This was probably the easiest gift purchase I have made online this season!
Ridley Park, PA
Wiring Adapter Fitguide
Trailer Wiring Manufacturers
Trailer Wiring Harness Installation - 1999 Chevrolet S-10
Today, on 1999 Chevrolet S10, we'll be installing the T-One Vehicle Wiring Harness with the 4-Pole Flat Connector, Part Number 118359. We will start our wiring installation by disconnecting the factory wiring connectors for the brake lights. To disconnect the wiring harness, push up on the white locking tab and pull towards the rear of the vehicle. Before we install our new wiring harness, we're going to add some electrical contact grease. We also sell this grease on our website. It's Part Number 11755. Let's put it off on there to cover all the contacts with the grease on the connectors. We can just plug our new wiring harness into the factory wiring connections. Next, we will use our factory ground to ground our wiring harness, too.
Trailer Wiring Harness Installation - 2002 Chevrolet S-10
Today we are going to be installing Tow Ready T-One connector, part number 118359 on our 2002 Chevy S-10. So first we are going to gently pry back on our connector and separate our rear taillight harness. Then we are going to take our new wiring harness. As you can see, it looks almost identical to the manufacturer harness. We are going to install it in line with the manufacturer harness. Press firmly when installing the connectors so that the locking tab goes back in to place. With our second connection, again our locking tab is in place. Now let us locate a suitable place to install our ground wire. I like to use a self-tapping screw when installing my ground wire. We are going to run it right in here to the bottom of our frame. 2:10
Wiring Harness Installation - 2003 Chevrolet S-10
Today on this 2003 Chevrolet S-10 we are going to install part number 118359 from Tow Ready. The T-One wire harness will install on the driver side frame rail at this connection point. We will disconnect it and install the T-Connector. These snap together. The last thing you have to deal with is the ground wire. Just use a self tapping screw and run it right through the bottom of the frame. Now we will take our wiring harness and route it over to our hitch. We will zip tie the wires to the license plate lights and that will keep it safely out of the way. We are already finished. There you have it for part number 118359 from Tow Ready.
Trailer Wiring Harness Installation - 1993 Chevrolet S-10 Pickup
Today on this 1993 Chevrolet S-10 Pickup truck we are going to install part number 118312 from Tow Ready, their T-One wiring connector. On the driver side frame rail of the vehicle you will see a connection point for the electrical harness right here. What you need to do is take the harness and split it apart and insert the T-One. It snaps right back into place. Then the other half. Then we will take our ground wire and ground it to the bottom of the frame right here. We will take our 4-pole wiring harness and we will just run it along the factory wiring and out to our hitch ball on our bumper. Use a few zip ties to hold everything in place and we will be good to go. Get rid of the excess and with that our install is complete. There you have it for part number 118312 from Tow Ready.
Subscribe to email newsletter
privacy - we don't send unsolicited email
All images, layout and content copyright etrailer.com