See what our Experts say about this Bulldog Camper Jacks

• Replacement Square Tube Bulldog Jack with Number 015796
  Sounds like you are looking for a replacement Bulldog Square Tube jack like part # BD182800 which matches the capacities and sizes you mentioned.
  view full answer...
• What Country is Bulldog Jack part # BD182800 Made In
  The Bulldog Jack part # BD182800 that you referenced was made in Mexico so it would work well for what you need. In the attached picture you can see "Made in Mexico" on the sticker label.
  view full answer...
  
• Replacement Electric Landing Gear for Horse Trailer
  Sorry to hear your system broke and there aren't replacement parts available for your horse trailer. The Bulldog Velocity Series Electric Landing Gear Jack - 24" Lift - 12,000 lbs # BD185400 is a good replacement for your discontinued and broken system. It will simply bolt right on to your trailer so it can utilize the 12V power you already have run. It is able to lift 12,000 lbs and lifts 20 inches in 60 seconds. Another great option for you is the Bulldog Square Jack - Drop Leg w/...
  view full answer...
• Replacement Drop-Leg Pin for Bulldog Heavy-Duty Square Jacks
  No, I am sorry Cesar we do not. I saw you were looking at the Bulldog Square Jack item # BD182800. The correct replacement drop-leg pin is the item # BD500177. What capacity is your Bulldog square jack?
  view full answer...
• Replacement Return Spring for Bulldog Square Jacks
  The return spring inside the Bulldog Square Jacks like part # BD182800 are neither replaceable nor repairable according to Bulldog. Therefore, so you will have to replace the entire jack if yours is broken or damaged.
  view full answer...
• Replacing the Drop Leg Spring Loaded Pull Pin on a Bulldog 180 Series Square Jack
  For a Bulldog 180 series jack you will need replacement drop leg pin # BD500177. It includes the spring, cotter pin, and washer. You should not have to remove the inner drop leg to replace the pin and spring. Start by pulling back on the pin. Then use whatever tool will fit to pull out the cotter key. Then everything should come out. Then you will put on the spring, washer, and the cotter key goes on last to hold it all in place so put it back in the way that it came out. The spring...
  view full answer...
• How To Convert Diamond C Gooseneck Flatbed Jacks From Manual To Power
  The best and only option I have for you to add electric jacks to a gooseneck trailer is to first replace the existing drop leg jacks with the Bulldog Square Jack part # BD182800 and part # BD182805 as this would then allow you to convert them to electric using the Bulldog Powered-Drive Kit part # BD1824200100 (2). I really wish we just had a motor you could use with your existing drop leg jacks but that is not the case as the motors are not universal. Therefore, you need to pair the motor...
  view full answer...
• Difference Between Bulldog Square Sidewind 10,000 Lb Weld-On Landing Gear Trailer Jacks
  The Bulldog Square Jack, part # BD182800 and part # BD182815 are very similar but have just a couple of slight differences. They are both 26 inch lift jacks with a 10,000 lb weight capacity, and are sidewind jacks. The # BD182800 has a side-facing plunger pin and has a 27-2/5 inch retracted height. The # BD182815 features a front-facing plunger pin and when retracted has a height of 28-1/2 inches. As you can see there are a couple of differences.
  view full answer...
• Recommended Landing Gear for Hillsboro 300 Gooseneck Trailer
  On your 1998 24K Hillsboro 300 gooseneck trailer, the Stallion Landing gear is not a brand I'm familiar with. The Replacement Screw and Nut Kit for 12000-lb Capacity Bulldog Jacks # BD500217 is not welded in and has a 2 inch by 2-3/4 inch nut on a threaded 1.25 inch diameter screw. Because you say the nut may be welded, I recommend changing out the jacks completely with the Bulldog Square Jack - Drop Leg w/ Spring Return - Sidewind - 12-1/2" Lift - 10,000 lbs # BD182800. I've attached...
  view full answer...
  
• Shelby Side Wind Trailer Jack, Part # 6108SW for Triton Trailer
  I think the Square Pipe Mount Swivel, part # TJDP-7000S-B would be a good choice for you. It has the 8,000lb support capacity which is one of the highest we offer, and is welded to the trailer frame.
  view full answer...
• Is There a Power Drill Attachment for a 12K Trailer Jack
  It sounds like you have something like the Bulldog Square Jack part # BD182800 and if that's the case then I do have an option for you to achieve faster and easier operation. However, there isn't any sort of drill attachment for these jacks. That said, there is a manual to power conversion for the model above, the Bulldog Powered-Drive Kit for Single-Speed Jacks part # BD1824200100 which is what I recommend as it's really your only option for faster and easier operation.
  view full answer...
• Trailer Jack Recommendation for Horse Trailer
  The Bulldog jack part # BD182800 would be an excellent choice for a jack for your horse trailer. It has a 10k capacity and then for a handle the part # BD800090 would work well. The jack has a drop leg as well which will
  view full answer...
• Recommendation for Electric Trailer Jacks on a 48 Foot MTI Gooseneck Race Car Trailer
  We have two options that would work for your MTI 48ft. gooseneck trailer. Option #1: Ultra-Fab Products Trailer Jack -# UF17-943010 - with this option it has a combined weight capacity of 12,000 pounds, which will currently hold your trailer and race car providing that the weight at the front of the trailer does not exceed the 12,000 pound recommendation. If you decide to add more weight in the future, you will want to re-look at your jack situation. This item has a 3 year warranty....
  view full answer...
  
• Replacement Bulldog Tandem 2-Speed Jack Recommendations
  The only tandem Bulldog Jack set with 2 speeds that we offer is the Bulldog 2-Speed Tandem Landing Gear Set # BD500153. Which if you needed them individually you would want part # BD1823050383. This jack set has a 45,000 lb capacity and does not have a spring release handle like you said you have though which makes me think you may have something different like the part # BD182800 that you referenced which is actually a single speed jack. If you need a repair kit for the spring return...
  view full answer...
• Replacement Plunger Pin Recommendation for a Bulldog Landing Gear Square Jack
  For a Bulldog 180 series jack you will need replacement drop leg pin # BD500177. It includes the spring, cotter pin, and washer. You should not have to remove the inner drop leg to replace the pin and spring. Start by pulling back on the pin. Then use whatever tool will fit to pull out the cotter key. Then everything should come out. Then you will put on the spring, washer, and the cotter key goes on last to hold it all in place so put it back in the way that it came out.
  view full answer...

Do you have a question about this Camper Jack?