Will Curt Trailer Hitch Receiver Fit 2025 Ford Mustang GT With Active Valve Exhaust
Will a Curt C45RJ hitch fit a 2025 Mustang GT with active valve exhaust? If not, do you offer another Class 1 hitch that will fit? | Hi Doug; the Curt Trailer Hitch Receiver # C45RJ is a pre-order item. Since it hasn't been fully developed...
Replacement Hub, Drum and Brake Assemblies for AL KO 3,500 lb Axle
I have a 2008 Flagstaff camper with two Alko axles. It is in need of new brakes/drums. Ive attached a photo of the plate attached to the front axle. Could you reference me to the proper parts, drums and brakes, including seals and dust caps...
Recommended Replacement Hydraulic Pump Motor for a Lippert Leveling System
is the 172911 the replacement for 414850 on a Lippert leveling systems? | Tan, it actually looks like the Replacement Hydraulic Pump Motor for Lippert RV Leveling Systems # LC57AF is the correct replacement for your Lippert 414850. To get...
2018 Mustang GT Trailer Hitch Recommendation
I just returned from my local garage where they tried to install a Curt 11405 only wifes new 2018 Mustang GT. The Curt 11405 was originally on her 2015 Mustang ecoboost. The hitch does not fit the 2018 GT because the mufflers interfere with...
Troubleshooting Curt Trutrac System Digging Into Brackets
I recently purchased the Curt Trutrac WD C17501 for my 2004 Ford Excursion towing a 39ft travel trailer. The tongue weight loaded is around 1100 lb. The RV dealership installed the weight distribution on my trailer and set it up but after driving...
Best Trailer Hitch For 2025 Ford Mustang Ecoboost
I need a trailer hitch for a 2025 Ford Mustang Ecoboost. A class 1 1.25 hitch would do. You show a Curt hitch available in September. What are the odds of this happening in that time frame ? | Hello Denis, thanks for reaching out. The correct...
Trailer Hitch, Wiring and Ball Mount for 2017 Ford Mustang
10” rise from 1 1/4 to 2” I don’t need dual. Just small to large with 9 or 10” rise - I need to go from 1 1/4 to 2” with 10” rise to carry electric wheelchair on my 2017 mustang. Car is low and 5” rise drags | There is a potential way for you...
Recommended Air Bags for a 2005 Ford Econoline 350 w/ a V10
I have a 2005 Ford Econoline 350 with V10. It has a 3 inch lift. Do you have any rear air suspension products that would work with the lift. I want to tow with it and I am a huge fan of of the rear suspension airbag systems. | Hey Russell, we...
Trailer Hitch that Fits 2021 Ford Mustang California Special
Hello, Would like to know which bike hitch will fit my 2021 California Special GT Mustang. Thank you! Eve | Hey Eve, we have the Curt hitch part # C11405 that does fit your 2021 Ford Mustang California Special. Are you also looking for a bike...
What Other Vehicles Will the Superchips Flashpaq F5 Performance Tuner SU2845 Work On
I sold my truck, is this thing useless now? | The Superchips Flashpaq F5 Performance Tuner part # SU2845 will work with many different vehicles which I have attached a list of for you below. That said, in order to transfer the device from one...
Mounting Hole Measurements for Derale 17" Fan Clutch Fan
What is the measurements from center of hole to hole? There are two options for mounting. What is each of the measurements for these two options? | Hey Darin, thanks for reaching out! The mounting holes for the Derale 17" Fan Clutch Fan #...
Will a 4.80-8 Trailer Tire Fit in Place of a 4.00-8 Tire
I have seed planter with implement tires of 4.00 x 8. Will a 4.80 tire fit? | Yes, a 4.80-8 tire will fit in place of a 4.00-8 tire. That is why a lot of times you will see both sizes in the product's title or description and even on the actual...
What is Max Amperage Draw of Bulldog Winch Light Duty On-Board Air Compressor
What is the maximum amp draw of this compressor? | Hey Michael, the Bulldog Winch Light Duty On-Board Air Compressor # BDW46TJ draws at max just under 40 amps. |
Which Kat's Block Heater Fits 2025 Mitsubishi Outlander SE 2.5 Liter
Will this heater work, without modification, on my 2025 Mitsubishi Outlander SE? Please confirm the location for this vehicle as well. | Hey James, yes the Kat's Heater part # KH11812 that you referenced is a confirmed fit for your 2025 Mitsubishi...
What Rack System Can I Use On My 2002 Ford Excursion With Factory Side Tracks
Will this fit the factory tracks of a 2002 ford excursion? | Great question, Dave! After some double checking I can confirm that Rhino Rack part # Y02-480B-NT will work on the factory tracks on the roof of your 2002 Ford Excursion. What are...
Looking For A Shocker Hitch For My 2003 Ford Excursion Pulling A 7k Trailer
I am interested in a shocker hitch. I have a 2003 ford excursion, 7.3 l diesel with 4 wheel drive. I primarily pull a RV that weighs 7,000 lbs. What model do you recommend? thanks | Hey Patrick, The Shocker Hitch # SHK47VR would be a solid...
Looking For Replacement Weather Stripping For Lift Gate On 2003 Ford Excursion
I need to replace the weather stripping for the lift gate on my 2003 Ford Excursion and the OEM Part 2C7Z-78404A06-AA has been discontinued. I have been searching junk yards and the internet for something that might work. Might you have something...
What To Do When The Air Lift Air Bag Helper Spring Fails During a RV Trip?
I have the 5000 Air Lift series bags on my 2WD Ford Excursion, and during the beginning of our three month RV trip the passenger side will not hold air. Troubleshooting my a local mechanic indicates bag is damaged. What recourse do I have while...
Dimensions of Draw-Tite Trailer Hitch Receiver # 76015
can you give me the inside horiz width from the bottom two holes on each side in inches ? e.g. 48.5 or 51etc also the vertical height from the top of the receiver bar to the bottom of the same two holes, thanks | The Draw-Tite Max-Frame Trailer...
Troubleshooting Open Ground Warning on P3 with Known Solid Ground Connection
I have the Prodigy P3 installed on my 2003 Excursion 6.0L diesel using the 3035-P adapter. Intermittently I get the Open Ground No Brakes warning message. No trailer connected. I checked the batteries negative terminal to chassis in the engine...
Troubleshooting 2011 Ford Mustang Curt Wiring Without a Solid Ground
I have installed this and double checked my wiring connections, but every pin on the 4 pin connector is solid on except ground. I am thinking there is something wrong with the module itself. Please advise. Thanks | Hey John, thanks for reaching...
Can Tongue Weight of Curt # C11041 be Increased for Use on a 1999 Ford Mustang
Is thair any custom modifications i can do to the hitch to increase the tounge weight? | The weight capacities of trailer hitches, like the Curt # C11041 for your 1999 ford Mustang, cannot be enhanced. Trailer hitches are tested extensively...
Curt Wireless vs Prodigy Wireless for Motorhome Towing
I need a trailer brake controller for my 22foot enclosed trailer. I was thinking of going wireless so I wouldnt need to access the MH wiring to install. What is your recommendation. | Performance-wise the Prodigy RF part # TK94FR and the Curt...
Why Choose a Powered Taillight Converter Over a Non-Powered Model
What dictates the need between using a powered Tail light convertor Vs a non powered? | There's a couple of factors that determine that. On older vehicles, very few vehicles needed a powered converter, because the vehicle's electrical system...
Filter Your Search
Contact and Help