Recommended Trailer Brake Controller for Use in 1984 Chevrolet K20 Pickup

Question

Question:

I have a1984 chevy k20 pu and I want to wire it up for electric brakes what do I need as well as getting good instructions

asked by: Steve

0

Expert Reply:

To install a trailer brake controller in your 1984 Chevrolet K20 Pickup you will need the brake controller itself, such as the excellent Tekonsha Primus IQ # TK90160 that you referenced, as well as a brake controller installation kit # ETBC7. If your truck does not already have a working 4-pole flat trailer connector you will also need one those, part # 118311.

Your installation will be a hard-wire type since there is no quick-connect port under the dash. At right you will find links to a video and articles concerning installation of the # ETBC7. These will give you step by step guidance for the installation.

expert reply by: Adam R

0

James L.

4/13/2020

I have a 86 chevy 1ton k30 military pick up. I need all hardware and wiring for electric trailer brake.

Chris R.

4/14/2020

If you don't yet have a trailer connector on your K30 you'll need to start with a 4-Way, the Tekonsha # 118312. From there you can upgrade it to a fully functional 7-Way using the Wiring Kit # ETBC7 that Adam mentioned above. I like his recommendation of the Primus IQ # TK90160 as well. This will give you everything you need.

Answer 1

Your Flagstaff E Pro 12SRK will have the Go Power Retreat Solar Charging System with Digital Solar Controller #34272635 installed at the factory. You can add up to an additional 4 Solar Panels #34272634 with the your 30 amp charge controller. Each…

view full answer...

Answer 2

I would love to help but there's a lot to unpack here so perhaps taking a look through our help articles on solar energy first which I have attached for you below, will better serve you. That said, the Go Power Retreat Solar Charging System with…

view full answer...

Answer 3

Your best bet would be to temporarily remove the aftermarket hitch. This would allow you more room to access the nut holding the ball to the bumper. Completely saturate the nut with spray lubricant. If it is still stuck, you can try slipping a length…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Recommended Trailer Brake Controller for Use in 1984 Chevrolet K20 Pickup

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching