Where is the Connector for the Custom Fit Wiring Harness on the 2003 Honda Element

Question

Question:

where does it plug in on 2003 honda element?

asked by: James

0

Expert Reply:

You will need to remove the spring loaded hinged cover and the passengers side trim panel to access the wiring in the rear of the vehicle. The instructions (see link) have pictures to show exactly where the connector should be. Page 5 shows the instructions for the 2003-2004 Honda Element.

expert reply by: Robert G

0

Answer 1

The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #C55336 is a fit for the 2003 Honda Element. I've attached the installation video of a 2005 Pilot which is a similar install to assist. I've also linked the…

view full answer...

Answer 2

As far as how the Curt and Tow Ready trailer wiring harnesses for the 2004 Honda Pilot function and install they are the same. The guts in each of the converter boxes is not quite the same. The Curt harness #C55336 uses surface mount circuitry…

view full answer...

Answer 3

The Hopkins Wiring #HM11141995 and Curt Wiring #C56331 for your 2011 Dodge Grand Caravan install the same way but the Curt wiring is much more reliable, which is something you can see right away since the Curt has a 1-year warranty and the Hopkins is…

view full answer...

Answer 4

You could use either the Hopkins harness you were looking at, part #43105, or you could use the Tow Ready part #118336. They are comparable parts that install the same way. I have included a link to the Tow Ready part instructions that are very good.…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Check out page 5 of the instructions I attached for the Tow Ready Custom Fit Vehicle Wiring #118336. This is a different brand connector but it does the same thing as the Hopkins Custom Fit Vehicle Wiring #43105 and installs the same way so the…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Where is the Connector for the Custom Fit Wiring Harness on the 2003 Honda Element

Continue Researching