Replacement Parts for Fulton F2 Trailer Jacks

Question

Question:

I have some how managed to break a part inside my jack. This makes cranking my jack almost impossible. I was wondering if it is possible to purchase the top housing for my F2 1600. The part broken is the bushing that holds the main gear, This gear connects to the crank. Thanks a bunch guys.

asked by: John M

1

Helpful Expert Reply:

For replacement parts for your F2, we have a pull pin # F500136, handle # F500134, and gear cover # F500135. We no longer have gears or bushings for the F2, You may need an entire new jack.

expert reply by: Michael H

1

click to enlarge

Answer 1

We do have the Replacement Pull Pin Kit #F500136 which is the part number 18 in the photo you found. We do not carry the part number 4 for the Fulton F2 Trailer Jack #F1413040134 at this time so you may need to replace the parts from another damaged…

view full answer...

Answer 2

The Fulton F2 Swing-Up Trailer Jack #F1413040134 (as well as other F2 jacks) has that plastic piece that as you referenced is #9 in the exploded diagram. I reached out to my tech contact at Fulton and unfortunately that is not a replaceable part. You…

view full answer...

Answer 3

The ARK trailer jack part #ARK57FR uses a dual wheel setup with rubber tires that were designed for getting over off-road terrain which will be much easier to move by hand but the easiest would be the Trailer Valet 5X part #STC-V211 which comes with…

view full answer...

Answer 4

I attached a picture that has the measurements of the mounting holes on the mounting plate of the Dutton Lainson Sidewind jack #DL22339 that you referenced. Basically they are 5-1/2 inches from left to right and then 2-3/8 top to bottom row and then…

view full answer...

Answer 5

I have attached two diagrams below with the dimensions for the XO350 and XO750. Both of these use a bolt on installation so you really only need to know the height of your tongue to see if it is compatible. The #ORJW350D fits 2" to 6" tall…

view full answer...

Answer 6

The mounting plate on the ARK Removable Extreme Off-Road Swing-Up Trailer Jack #ARK57FR is 5-1/2" wide and 7-1/2" tall. It is designed with several bolt hole patterns(see image) to fit trailer tongues from 2-6" tall.

view full answer...

Answer 7

With the ARK Xtreme Off-Road Swing-Up Jack #ORJW500D in its lowest position it is 6.49" from the center of the mounting point to the top of the jack. The other end of the jack when fully retracted is going to be 18.89" from the mounting…

view full answer...

Answer 8

I went out to the warehouse and pulled one of the Pro Series Snap-Ring Swivel Jacks, #PSEJ10000101, to measure for you. I added dimensions to a photo I took of the mounting plate for you to use to see if the mounting pattern will match up to your…

view full answer...

Answer 9

No, Sheldon I am sorry we do not. Additionally, I checked with Fulton and they do not offer what is labeled part number 9 on the exploded diagram listed below. If you need to replace this part you will most likely have to purchase a new Fulton F2…

view full answer...

Answer 10

For your Fulton F2 Swing-Up Trailer Jack, Dual 7" Wheels, Sidewind, Bolt-On - 1,600 lbs #F1413020134 part number 9 you referenced is not a replacement option. The outer tube components are not replaceable according to my contact at Fulton. That…

view full answer...

Answer 11

Hi George; there are some replacement parts available for the Fulton F2 Boat Trailer Jack #F1413020134. We have the following: -Replacement Handle and Crank Kit for Fulton F2 Swing-Up Jacks #F500134 -Replacement Pull Pin Kit for Fulton F2 Swing-Up…

view full answer...

Answer 12

I recommend replacing the jack as that part #9 that you referenced in the diagram is not replaceable according to Fulton. The Fulton F2 Swing-Up Trailer Jack #F1413040134 is a similar sidewind wide-wheel jack and will bolt onto a 3"x3" or…

view full answer...

Replacement Parts for Fulton F2 Trailer Jacks

Featured Help Information

Miscellaneous Media

Continue Researching