Looking for Snapper Pin Replacement for Demco EZ Latch Coupler

Question

Question:

I lost the safety pin on my Demco coupler. What sI’ve should I purchase?

asked by: Jon F

0

Expert Reply:

You'll need a 3/8 inch diameter snapper pin like the part # 38-212TR.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

Hey Ken! Instead of worrying about fitment and a potential return I can give you some measurements so you can figure it out before ordering. The standard shank on the B&W Continuum Weight Distribution System #BW28FR is 11-3/8" from the…

view full answer...

Answer 10

We do! What you're looking for is the Under-Bed Rail and Installation Kit for Reese Elite Series 5th Wheel Trailer Hitches #RP87FR. This is the exact same setup that would have been installed on your 2022 Ford F-250 Super Duty if it had the OEM…

view full answer...

Answer 11

Hey Don, thanks for reaching out! The correct fit for your 2024 Ford F-250 with the Tremor package is the Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR. I confirmed with my contact at Hellwig that this will fit specifically with your Tremor…

view full answer...

Answer 12

Hello Travis, thanks for reaching out. No, the Curt T-Connector Vehicle Wiring Harness #C69CR is not going to be long enough to reach from the factory 7-way to the back of the bed on a 2022 Ford F-350. If you need to add a 7-way to the bed, you will…

view full answer...

Looking for Snapper Pin Replacement for Demco EZ Latch Coupler

Product Page this Question was Asked From

Continue Researching