Looking for Front Jack Leg Replacement for Lippert Ground Control 3.0 of 2019 Highland Ridge MBH 371

Question

Question:

Looking for replacement front jack for Lippert leveling system on 2019 Highland Ridge MBH 371 Fifth Wheel. Appears gears are stripped on left facing RV from front front jack and we are in the middle of a lengthy RV trip. Need to get it ASAP at one of our upcoming stops.

asked by: Jerome M

0

Expert Reply:

Hey Jerome, it sounds like you have a Lippert Ground Control system on your 2019 Highland Ridge MBH 371 which would mean for a replacement front jack leg you would want the part # LC362485 for a replacement. Does what you have now look like this but with a motor that attaches to the top of it?

expert reply by: Jameson C

0

Jerome M.

7/1/2026

Thanks for the reply. I was able to locate a replacement jack at a dealership along my RV trip route.

Jameson C.

7/1/2026

@JeromeM glad you were able to find one on the way! That's really convenient!

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 3

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

Hey Jerome, it sounds like you have a Lippert Ground Control system on your 2019 Highland Ridge MBH 371 which would mean for a replacement front jack leg you would want the part #LC362485 for a replacement. Does what you have now look like this but…

view full answer...

Looking for Front Jack Leg Replacement for Lippert Ground Control 3.0 of 2019 Highland Ridge MBH 371

Product Page this Question was Asked From

Continue Researching