Can Dometic 410 Toilet Replace 310

Question

Question:

I currently have a 2018 Forest River Rockwood Mini Lite Model 2509s. It has a Dometic 310 toilet. Will the Dometic 410 toilet fit?

asked by: Keary K

0

Expert Reply:

Hey Keary, yes the Dometic 410 RV Toilet part # DMC44JF will replace a Dometic 310. These two toilets are very similar so they are interchangeable.

expert reply by: Jameson C

0

Dometic 410
(click to enlarge)

Answer 1

If you already have brake drums you will not have to replace them unless they are damaged or became overheated and have discoloration on the inside armature surface where the magnet rides, grooves in the armature surface, or severe wear where the…

view full answer...

Answer 2

Hey Jeffrey, the Dometic RV toilet part #DMC44JF is designed to fit toilet applications with a 7-5/8 inch rough in measurement which is the measurement you took. Since your current setup has 10-1/4 inches this would work with space to spare. What…

view full answer...

Answer 3

Hey Jon, typically people replace the Dometic 310 RV toilet with the 410 which we have with the part #DMC64JF for a tan porcelain or the part #DMC44JF for a white porcelain. These are both standard height toilets with a round bowl and a slow close…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Can Dometic 410 Toilet Replace 310

Product Page this Question was Asked From

Continue Researching