Looking for Replacement Grease Seal for 6k Dexter Axle

Question

Question:

Looking to order 4 hub/bearing seals. My axel info Dexter 9665867 S/N 131310362012 6000 lb axels Can you help me out with this? Thanks!

asked by: Tim H

0

Expert Reply:

Hey Tim, for a 6k rated trailer axle from Dexter the correct replacement seal would be the part # GS-2250DL.

expert reply by: Jameson C

0

Tim H.

5/19/2026

Hey thanks for getting back to me! Is the $15.05 a piece? Thanks Tim.

Jameson C.

5/19/2026

@TimH It is but oddly enough you can get a pair for less money with the part # RG06-070.

Jay

5/20/2026

Worked perfectly on my 6000lb lip pert axle hubs. No issues. Easily installed flush with hub using wood block.

Answer 1

Hey Steven, since we know you have a 6k rated axle the correct bearing kit that includes a grease seal would be the part #BK3-100. Did you have bearing issues or are you looking for a backup set to keep around just in case?

view full answer...

Answer 2

The seal for your Dexter 4,400 lb axle is part #58846 which we also have in a pack of 2 listed as part #RG06-050 these have an inner diameter of 1.719" and an outer diameter of 2.565".

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Looking for Replacement Grease Seal for 6k Dexter Axle

Product Page this Question was Asked From

Continue Researching