Looking For Bolt Used To Connect Yakima HoldUp 2-Bike Add-On To Base Rack

Question

Question:

Hello, I have the Yakima Plus 2 2-Bike Add-On for Yakima HoldUp for 2inch Hitches, Part Number: Y02446 However, I lost the small screw that connects the Add-on 2 bike rack to the main 2-bike rack that connects to my trailer hitch. Do you sell the specific screw that will connect the two bike racks? I could not find the part number in the manual or on your website. Im sure you sell it but I want to make sure I buy the correct replacement part. V/r, Dave

asked by: Dave T

0

Expert Reply:

Hello Dave, thanks for reaching out. Yes, we do have the bolt used to connect the 2-bike add-on to the Yakima HoldUp # Y02446 rack. For that you'll need the following:

- Replacement Hitch Bolt for Yakima HoldUp 2, OnRamp, and BigHorn Bike Racks and DryDock Canoe Carrier # Y8890200

What kind of bikes do you have?

expert reply by: Jesse M

0

Yakima HoldUp 2-Bike Add-On Bolt
(click to enlarge)

Donna S.

5/6/2026

I just contacted etrailer and they immediately sent me the parts

Jesse M.

5/6/2026

@DonnaS Nice! Glad we were able to help you out. Thanks for sharing!

Answer 1

For your Yakima OnRamp Bike Rack #Y96FR that has the 1-1/4" hitch tube you will need the Replacement Tongue Assembly #Y99TR. This will replace your hitch tube and give you a 2" hitch tube for mounting your bike rack. The Replacement Tongue…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 4

Hello again, Dan. Thanks for writing in. The Demco Stay IN Play DUO Inline Air Pressure Regulator #DM88UV will not be needed for your 2025 Maverick Hybrid. You can still install one to lessen the braking pressure if it seems too harsh, but it…

view full answer...

Answer 5

Hi Bruce! The Access Toolbox Edition Soft, Roll-Up Tonneau Cover #A63FR will indeed fit your 2021 GMC Serra 1500 SLT with the short bed and your toolbox. This can be used with toolboxes that measure 19" to 21" long, so you are good to go!…

view full answer...

Answer 6

It sure is Doug and congrats on your new truck! The TruXedo Pro X15 Soft Tonneau Cover item #TX33TV has been confirmed to fit your new 2026 Ford Maverick. The TS Rails item #TH25FR are going to fit alongside the rails of the Pro X15 item #TX33TV on…

view full answer...

Answer 7

Hey Alan! The Demco Tabless Base Plate Kit #DM77YV won't have any issues working with the Roadmaster Nighthawk All-Terrain Tow Bar #RM-676. You will also need an adapter #DM9523062 to make the two compatible. For the rest of the parts I recommend…

view full answer...

Answer 8

Hey Mike, thanks for reaching out. Yep, the Victron SmartShunt 500A #VN43ZR will work just fine with a 24-volt lithium battery bank. It's compatible with battery systems from 6.5 to 70 volts, so a 24V LiFePO4 setup is well within its operating…

view full answer...

Answer 9

Hey Sean, welcome back! We do have a video showing the B&W Turnoverball #BWGNRK1320 being installed on a 2022 Ram 3500. I have provided a link to the video below. We don't have any videos showing how to remove the factory puck system though,…

view full answer...

Answer 10

Hey Jeff, yes the Pace Edward Switchblade tonneau cover part #PE66QJ that you referenced will definitely work with your Magnum headache rack. Your headache rack attaches to the top of your bed rails and this tonneau cover installs between the bed…

view full answer...

Answer 11

Hi Russ; you pretty much have everything you need right there with the exception of a few parts. I'm going to go ahead and list it all out here with links to make it easy for your to manage. You will need the following: -etrailer Invisible Base…

view full answer...

Answer 12

Hey Tom, the brake relay part #RM-88400 and the brake switch kit part #RM87GR actually do two different things. The brake switch kit is an easy way to get the stoplight signal isolated to trigger a braking system whereas the brake relay part…

view full answer...

Looking For Bolt Used To Connect Yakima HoldUp 2-Bike Add-On To Base Rack

Product Page this Question was Asked From

Continue Researching