Looking for Picture of Curt Hitch C96CR Installed

Question

Question:

Looking for an image of this hitch installed.

asked by: Matt

0

Expert Reply:

Hey Matt, while we haven't had the chance to get a picture of the Curt hitch part # C96CR installed we have had chance with the 2 inch version of the hitch part # C35CR which I attached below. It's on a truck with a service body though so that may or may not be what you are looking for.

expert reply by: Jameson C

0

Curt Hitch
(click to enlarge)

Answer 1

Hi Eric, Thanks for your question. As long as you are able to remove the factory hitch from your 2025 GMC Sierra 2500, the #C96CR will work as a replacement. Of note, the #C96CR will more than likely mount up a bit differently than your factory…

view full answer...

Answer 2

Congrats on the new truck! Our highest capacity bumper hitch for a 2024 Chevy Silverado 2500 is the Curt Trailer Hitch item #C96CR. This hitch is custom fit and bolts to your Silverado with included hardware. You will need to remove the factory hitch…

view full answer...

Answer 3

The Acme 91708 is a class 5 receiver hitch for a 2020-2021 Chevrolet/GMC Silverado/Sierra 2500/3500HD. I recommend the Curt Trailer Hitch Receiver #C96CR for a replacement. It is rated for a Gross Towing Weight of 20,000lbs and Tongue Weight of…

view full answer...

Answer 4

Yes, as long as you remove all of the OEM hardware and brackets the Curt Trailer Hitch Receiver #C96CR will fit your 2020 Chevy Silverado 3500 without any issues. This does install a little differently though as it secures to the bottom of the frame…

view full answer...

Answer 5

If you are having issues with the hitch pin hole becoming oblong on the shank for the Equal-i-zer Weight Distribution System part #EQ37100ET then you need to make sure the hitch pin hole on your trailer hitch is not also oblong as this would then…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Looking for Picture of Curt Hitch C96CR Installed

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching