Grease Seal for Dexter 4,400 lb Axle

Question

Question:

What is the part number for the grease seal on my Dexter 4400lb axles?

asked by: Greg M

0

Expert Reply:

Hi Greg, I don't have a way to know for sure without more information. Can you give me the S/N off one of the axle tags?

expert reply by: Robin H

0

Greg M.

4/28/2026

Sure, S012118586

Robin H.

4/29/2026

@GregM can you email me a picture? They're telling me it isn't a valid number.

Greg M.

4/29/2026

Emailed you

Robin H.

4/30/2026

@GregM got it. You need # RG06-070.

Greg

4/30/2026

@RobinH Perfect! Just ordered four of them.

Kevin

4/30/2026

The seals worked great perfect fit Use permatex red on them

Answer 1

Hello Greg; the MaxxAir MaxxFan Rooftop Vent w/ Pivoting Fan #MA36WV can use any of the MaxxAir vent covers like the MaxxAir FanMate #MA00-955002 or MaxxAir II #MA86JR. I tend to prefer the FanMate since you can add the bug screen #MA00-955202. Both…

view full answer...

Answer 2

Hey Robert, thanks for reaching out! To replace the bearings and seal for your Dexter 4,400 lb axle you can either use out Bearing Kit #BK2-100 or the Timken Kit #TMK52VR. The 4,400 lb hubs use the same bearings and seal as the 3,500 lb axles which…

view full answer...

Answer 3

Hello Kevin, that’s a great comparison to make. The Deluxe models like #MA00-07500K are higher output - they move up to around 900 CFM and include powered lift, rain sensing, a built-in thermostat, and more speed settings. They’re designed for…

view full answer...

Answer 4

According to the Lippert Service Manual for the Lippert Electric Trailer Jack #LC285318. "Maintenance 1. Before each use, inspect the Power Tongue Jack and replace if bent or damaged. 2. If wiring is connected to battery terminal, inspect at…

view full answer...

Answer 5

This A-Frame Trailer Coupler w/ Round Jack Hole #CA-5280-RB is manufactured in China. We do have similar options like the Buyers Products A-Frame Trailer Coupler w Jack Hole #3370091595 and Demco 50-Degree A-Frame Trailer Coupler w/ Jack Hole…

view full answer...

Answer 6

The seal for your Dexter 4,400 lb axle is part #58846 which we also have in a pack of 2 listed as part #RG06-050 these have an inner diameter of 1.719" and an outer diameter of 2.565".

view full answer...

Answer 7

The hubs used by the Dexter 4400 lb axle are 3500 lb hubs that have had their weight capacity upgraded by using a LM67048 outer wheel bearing. A 4400 hub like the #8-407-5UC3-EZ would use the same #58846 grease seal as a 3500 lb hub would. Long story…

view full answer...

Answer 8

I do have an option for you but SuperSprings does not offer any additional spacers for the SumoSprings Trailer Helper Springs part #SS26MV. That said, we do still have spacers that will work for this, the Timbren Spacer part #A25723-90AH00 for…

view full answer...

Answer 9

Hey Michael, thanks for reaching out! The Shoulder Bolts #MR92HR and #MR52HR will fit with the Replacement Flange Nut #MR85DR . We don't have a specific one from MORryde that works, but they are both compatible with this one so it can be used…

view full answer...

Answer 10

The spacers included with the SumoSprings Trailer Helper Springs #SS26MV are required to get it the 6-1/2" height. Without the spacers the required clearance drops to 5-5/16". Per SumoSprings you can add additional spacers to fit the…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Grease Seal for Dexter 4,400 lb Axle

Product Page this Question was Asked From

Continue Researching