Bearing Kit for Dexter D44 Axle

Question

Question:

Trying to see if this kit is what I need. None of the numbers on the tag in the picture I provided match up. Hopefully yall can guide me in the right direction.

asked by: Scotty C

0

Dexter Axle Tag
(click to enlarge)

Expert Reply:

Hey Scotty, thanks for the picture! Your Dexter D44 axle uses the standard 3,500 lb bearing combination. You can use the Hub Bearing Kit # BK2-100 or if you want to stick with Dexter, the Dexter kit # DX76ER.

What trailer are you working on?

expert reply by: Robin H

0

Answer 1

Hey Robert, welcome back! The Dexter 010-036-00, our item #RG06-070, and the Timken item #TMK58ZR are functionally the same grease seal. Timken is known for using higher quality materials in their parts so they do cost noticeably more. Both the item…

view full answer...

Answer 2

Hey Steven, we have the individual components of a bearing kit available for a Dexter 4,400 lb trailer axle but since it's a rarer axle capacity we don't have a bearing kit. So for a Timken set you'd want the part #TMK49FR and #TMK56FR…

view full answer...

Answer 3

We have the individual components of a bearing kit available for a Dexter 4,400 lb trailer axle but since it's a rarer axle capacity we don't have a bearing kit. So for a Timken set you'd want the part #TMK49FR and #TMK56FR and then for a…

view full answer...

Answer 4

We do offer complete trailer bearing kits for a variety of combinations of inner and outer bearings, races and seals, but we do not happen to offer one that includes each of the components you require. You will then need to order the components as…

view full answer...

Answer 5

Yes, the Timken Bearing Kit #TMK52VR will fit your 3,500 lb axle as it fits an standard #84 spindle. The only time this kit won't fit with a 3,500 lb axle is if the trailer/axle is made before the 2000's since that's about the time that…

view full answer...

Answer 6

On Dexter axles manufactured after April 2001 you will be able to find the serial number stamped on the rear portion of the axle tube approximately 18" from the passenger side hub. Depending on the condition of the axle you may need some chalk…

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Bearing Kit for Dexter D44 Axle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching