Replacement Brakes for 2004 Laredo 5th Wheel With 12" x 2" Brake Assemblies

Question

Question:

Trying to find brakes that matches my 2004 Laredo 5th wheel, 2” x12” the web site pictures don’t match what I have a picture to send.

asked by: Larry M

0

Expert Reply:

Hey Larry! If they're 12" x 2" then you must have 5,200 lb to 7,000 lb axles with a 5 bolt brake flange. You can use the etrailer Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand - 5.2K to 7K # AKEBRK-7-SA for a replacement. If you still think that doesn't match up with what you have, or if you want to double check, you can respond to the email with the link for this page and send me your pictures. A picture of the axle tag would be good as well.

expert reply by: Robin H

0

etrailer Electric Trailer Brakes
(click to enlarge)

Chris P.

4/6/2026

Yes I used the 5200-7000 pound brakes on my 2008 Forestriver Wildcat. Replaced mine in December. They were very easy to install and so far have worked great. Have taken the unit on three trips so far and they actually skid the tires now. How to adjust the gain. LOL. Just five bolts per axle and two wire if bearings need packing pack them while you got them off quick brake adjust many and off you go. Only issue I did have was a couple of them came with the springs and shoes popped off the pin but that was a quick and easy fix before I ever put them on. Chris

Dave M.

4/6/2026

@Chris Perfect fit for our coachman liberty edition Dexter axles easy install so much better than original equipment manual adjusting brakes don’t forget to order new grease seals check and grease bearings while apart

Thomas

4/6/2026

I have replaced the original brakes on my Montana 35' 5w 2 times in the 10 years I have had it and used the brakes from e trailer on the Dexter axles both times. Very easy to change out and I had no problems at all.

Jeremy

4/6/2026

@Thomas... Larry, just buy something and put them on. It's either going to fit and work or won't. Or take it to a shop and pay them to do it correctly

Robert

4/6/2026

Hi Larry, These worked great for me on my 2010 Montana fifth wheel replacing the factory Dexter assemblies last year. The drums were slightly different size but have worked great so far.

Answer 1

Hey Tom, we have the correct hub/drum you are looking for with the part #42866UC3-EZ if you have 1/2 inch wheel studs or the part #8-219-13UC3 for if you have 9/16 inch diameter studs. Then for brake assemblies you'd just need the part…

view full answer...

Answer 2

Dexter brake assemblies like the part #23-458-459 are essentially the best ones on the market. They use the best materials and and incredibly reliable and well-made. That being said the etrailer.com brand assemblies part #AKEBRK-7-SA are also very…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Replacement Brakes for 2004 Laredo 5th Wheel With 12" x 2" Brake Assemblies

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching