Are DeeMax Rotors Interchangeable with KNOTT Brand

Question

Question:

HI. Id like to replace 12inch brake rotors on a loadrite trailer. I believe the brakes are KNOTT brand. Each side is 6,000 capacity. It looks like the bearings and races are the same part number. Is it possilbe that this rotor will fit? Thanks

asked by: Stephen S

0

Expert Reply:

Hey Stephen, with disc brake components on trailer axles you have to make sure the brand matches between all of the components as they are all slightly different. This is different than drum brakes where the parts are basically all interchangeable. So if you want to replace just the rotor you would need to check with Knott or go with an all new setup like the DeeMaxx # DE28YR.

Is the rotor you have now damaged?

expert reply by: Jameson C

0

Answer 1

From the numbers you provided it sounds like you need replacement grease seals. In my research, the grease seals I found with the GS-1719DL number have a 1.72 inside diameter and 2.565 outside diameter. The replacement double lip grease seals you…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Are DeeMax Rotors Interchangeable with KNOTT Brand

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching